HP A7500 Series Скачать руководство пользователя страница 188

Страница: 188 / 222

181

Field Remarks

Voltage low

Voltage is low.

Transceiver info I/O error

Transceiver information read and write error

Transceiver info checksum error

Transceiver information checksum error

Transceiver type and port configuration
mismatch

Transceiver type does not match port configuration.

Transceiver type not supported by port
hardware

Transceiver type is not supported on the port.

XFP

RX loss of signal

Incoming (RX) signal is lost.

RX not ready

RX is not ready

RX CDR loss of lock

RX clock cannot be recovered.

RX power high

RX power is high.

RX power low

RX power is low.

TX not ready

TX is not ready.

TX fault

TX CDR loss of lock

TX clock cannot be recovered.

TX bias high

TX bias current is high.

TX bias low

TX bias current is low.

TX power high

TX power is high.

TX power low

TX power is low.

Module not ready

Module is not ready.

APD supply fault

APD (Avalanche Photo Diode) supply fault

TEC fault

TEC (Thermoelectric Cooler) fault

Wavelength unlocked

Wavelength of optical signal exceeds the manufacturer’s
tolerance.

Temp high

Temperature is high.

Temp low

Temperature is low.

Voltage high

Voltage is high.

Voltage low

Voltage is low.

Transceiver info I/O error

Transceiver information read and write error

Transceiver info checksum error

Transceiver information checksum error

Transceiver type and port configuration
mismatch

Transceiver type does not match port configuration.

Transceiver type not supported by port
hardware

Transceiver type is not supported on the port.

Examples

# Display alarm information for the transceiver module in interface GigabitEthernet 2/0/1.

Содержание A7500 Series































































































































































































































Результаты поиска

Содержание A7500 Series

Отзывы:

Похожие инструкции для A7500 Series

Бренды по названию

Популярные бренды

HP A7500 Series, Справочник по командам

Результаты поиска

Содержание A7500 Series

Отзывы:

Похожие инструкции для A7500 Series

Бренды по названию

Популярные бренды