HP A7500 Series Скачать руководство пользователя страница 189

Страница: 189 / 222

182

<Sysname> display transceiver alarm interface gigabitethernet2/0/1

GigabitEthernet1/0/1 transceiver current alarm information:

RX loss of signal

RX power low

Table 30

Output description

Field Description

transceiver current alarm information

Alarms present on the transceiver module

RX loss of signal

Incoming (RX) signal is lost.

RX power low

Incoming (RX) power level is low.

display transceiver diagnosis

Syntax

display transceiver diagnosis

interface

[

interface-type interface-number

] [

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

2: System level

Parameters

interface

[

interface-type interface-number

]: Displays the present measured value of digital diagnosis

parameters of the transceiver plugged in the specified interface.

interface-type interface-number

represents interface type and interface number. If it is not specified, the command displays the currently

measured value of digital diagnosis parameters of transceivers in all the interfaces.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the

display transceiver diagnosis

command to display the present measured values of the digital

diagnosis parameters for transceiver modules.

Examples

# Display the present measured values of the digital diagnosis parameters for the transceiver module in

interface GigabitEthernet 2/0/2.

<Sysname> display transceiver diagnosis interface gigabitethernet2/0/2

GigabitEthernet1/0/2 transceiver diagnostic information:

Current diagnostic parameters:

Temp(°C) Voltage(V) Bias(mA) RX power(dBm) TX power(dBm)

36 3.31 6.13 -35.64 -5.19

Содержание A7500 Series































































































































































































































Результаты поиска

Содержание A7500 Series

Отзывы:

Похожие инструкции для A7500 Series

Бренды по названию

Популярные бренды

HP A7500 Series, Справочник по командам

Результаты поиска

Содержание A7500 Series

Отзывы:

Похожие инструкции для A7500 Series

Бренды по названию

Популярные бренды