HP 6125G Скачать руководство пользователя страница 292

Страница: 292 / 426

280

Table 64

Command output

Field Description

Interface group report information

IPv6 multicast group information created based on MLD SSM
mappings on the interface.

Total 1 MLD SSM-mapping Group reported One MLD SSM mapping multicast group was reported.

Group

IPv6 multicast group address.

Uptime

Length of time since the IPv6 multicast group was reported.

Expires

Remaining time of the IPv6 multicast group, where "off" means
that the group never times out.

Last reporter

IPv6 address of the host that last reported membership for this
group.

Group mode

IPv6 multicast sources filter mode.

Source list(Total 1 source)

IPv6 multicast source list (one IPv6 multicast source).

Source

IPv6 multicast source address.

Last-listener-query-counter Number

of MLD last listener queries sent.

Last-listener-query-timer-expiry

Remaining time of the MLD last listener query timer, where "off"
means that the timer never expires.

dscp (MLD view)

Syntax

dscp

dscp-value

undo dscp

View

MLD view

Default level

2: System level

Parameters

dscp-value

: Specifies the DSCP value for MLD messages, in the range of 0 to 63.

Description

Use

dscp

to set the DSCP value for MLD messages.

Use

undo dscp

to restore the default.

The default DSCP value in MLD messages is 48.

Examples

# Set the DSCP value to 63 for MLD messages.

<Sysname> system-view

[Sysname] mld

[Sysname-mld] dscp 63

Содержание 6125G











































































































































































































































































































































































































































Результаты поиска

Содержание 6125G

Отзывы:

HP 6125G, Справочник по командам, Страница: 292 / 426

Результаты поиска

Содержание 6125G

Отзывы: