HP 5830 series Скачать руководство пользователя страница 64

Страница: 64 / 66

LEDs

Table 23

LEDs at a glance

LED Availability

System status LED

Entire series

10/100/1000Base-T Ethernet port LED

Entire series

SFP port LED

48G model/48G TAA model

SFP+ port LED

Entire series

Management Ethernet port LEDs

Entire series

Interface card status LED

48G model/48G TAA model

System status LED

Every switch has a system status LED on both the front and rear panels. The two LEDs are the same
and concurrently show the operating status of the switch.

Table 24

System status LED description

LED mark

Status

Description

SYS

Flashing green

The switch has started up properly.

Flashing red

An alarm is generated.

Off

The switch is powered off.

10/100/1000Base-T Ethernet port LED

Each 10/100/1000Base-T auto-sensing Ethernet port has a status LED to show port operating status

and activities.

Table 25

10/100/1000Base-T auto-sensing Ethernet port LED description

Port LED status

Description

Steady green

The port is operating at 1000 Mbps. The port LED fast flashes when the port is
sending or receiving data.

Steady yellow

The port is operating at 10/100 Mbps. The port LED fast flashes when the port
is sending or receiving data.

Off

No link is present on the port.

SFP port LED

Each SFP port has a status LED to show port operating status and activities.

Содержание 5830 series



































































Результаты поиска

Содержание 5830 series

Отзывы:

Похожие инструкции для 5830 series

Бренды по названию

Популярные бренды

HP 5830 series, Руководство по установке

Результаты поиска

Содержание 5830 series

Отзывы:

Похожие инструкции для 5830 series

Бренды по названию

Популярные бренды