HP 5500-24G-SFP EI TAA Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 69

background image

18

3.

Loosen the captive screws of the power supply with a Philips screwdriver until they are completely

disengaged.

4.

Grasp the handle of the power supply with one hand and pull it out a little, support the bottom with
the other hand, and pull the power supply slowly along the guide rails out of the slot.

NOTE:

Put away the removed power supply in an antistatic bag for future use.

Connecting the power cord

WARNING!

Make sure the grounding cable has been correctly connected before powering on the switch.

Use

Table 5

to identify the power cord connection procedures available for your switch.

Table 5

Power cord connection methods at a glance

Chassis Connection

procedure

5500-24G EI (2 slots)
5500-24G EI TAA (2 slots)
5500-48G EI (2 slots)
5500-48G EI TAA (2 slots)
5500-24G SI (2 slots)
5500-48G SI (2 slots)

AC-input:

Connecting the AC power cord

RPS input:

Connect the switch to a +12 VDC output RPS

5500-24G-PoE+ EI (2 slots)
5500-24G-PoE+ EI TAA (2 slots)
5500-48G-PoE+ EI (2 slot)
5500-48G-PoE+ EI TAA (2 slot)
5500-24G-PoE+ SI (2 slots)
5500-48G-PoE+ SI (2 slots)

AC-input:

Connecting the AC power cord

RPS input:

Connecting the switch to a –52 to –55 VDC output RPS

5500-24G-SFP EI (2 slots)
5500-24G-SFP EI TAA (2 slots)

AC-input PSR150-A/PSR150-A1 power supply:

Connecting the AC power cord

DC-input PSR150-D/PSR150-D1 power supply:

Connecting the PSR150-D/PSR150-D1 to a –48 VDC
power source

Connecting the AC power cord

1.

Wear an ESD-preventive wrist strap and make sure it makes good skin contact and is well
grounded.

2.

Connect one end of the AC power cord to the AC-input power receptacle on the switch or the
power supply (see

Figure 17

).

3.

Connect the other end of the AC power cord to the AC power outlet.

«
...
21
22
23
24
25
...
»

Содержание 5500-24G-SFP EI TAA






































































Отзывы:

Нет отзывов

Похожие инструкции для 5500-24G-SFP EI TAA

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

i-bus KNX IPR/S 3.5.1

Бренд: ABB Страницы: 44

Power Xpert Meter 2000

Бренд: Eaton Страницы: 16

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 84

Бренд: National Instruments Страницы: 11

Бренд: Pima Страницы: 4

Бренд: Tripp Lite Страницы: 2

Бренд: Acces I/O products Страницы: 5

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Бренд: UNA AUTOMATION Страницы: 20

Бренд: SAGEMCOM Страницы: 75

Бренд: Renesas Страницы: 4

PXI PXITM -1000

Бренд: National Instruments Страницы: 55

Бренд: AC Infinity Страницы: 24

FiberTwist XGS2410

Бренд: Genexis Страницы: 7

Routers and Switches

Бренд: Allied Telesis Страницы: 15

Бренд: Paradyne Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды