HP 5500-24G-SFP EI TAA Скачать руководство пользователя страница 61

Страница: 61 / 69

LED Availability

RPS status LED

Entire series (except the 5500-24G-SFP EI (2 slots)
and 5500-24G-SFP EI TAA (2 slots) )

Port mode LED

Entire series

Seven-segment LED

Entire series

10/100/1000Base-T Ethernet port LED

Entire series

SFP port status LED

Entire series

Interface card status LED

Entire series

System status LED

The system status LED shows the operating status of the switch.

Table 12

System status LED description

LED mark

Status

Description

SYS/PWR

Steady green

The switch is operating correctly.

Flashing green (1 Hz)

The switch is performing power-on self test (POST).

Steady red

POST has failed.

Flashing yellow (1 Hz)

Some ports have failed to pass POST.

Off

The switch is powered off.

Power supply status LEDs

Only the 5500-24G-SFP EI (2 slots) and 5500-24G-SFP EI TAA (2 slots) switches have power supply status

LEDs to show the operating status of the power supplies in the power supply slots.

Table 13

Hot swappable power supply status LED description

LED Status Description

PWR1
PWR2

Steady green

A power supply is installed in the power supply slot,
and the power output is normal.

Steady yellow

A power supply is installed in the power supply slot,
but the power supply is experiencing an output error

or is not powered on.

Off

No power supply is installed in the power supply slot.

RPS status LED

The RPS status LED shows the operating status of the RPS DC input.
The 5500-24G-SFP EI (2 slots) and 5500-24G-SFP EI TAA (2 slots) switches do not have an RPS status

LED.

Содержание 5500-24G-SFP EI TAA






































































Результаты поиска

Содержание 5500-24G-SFP EI TAA

Отзывы:

Похожие инструкции для 5500-24G-SFP EI TAA

Бренды по названию

Популярные бренды

HP 5500-24G-SFP EI TAA, Руководство по установке

Результаты поиска

Содержание 5500-24G-SFP EI TAA

Отзывы:

Похожие инструкции для 5500-24G-SFP EI TAA

Бренды по названию

Популярные бренды