HP 54 Basic Cutter Скачать руководство пользователя страница 57

Страница: 57 / 58

Firmware

Language

DM/PL, HP-GL (758x emulation), HP-GL/2

Supported character sets

Standard ASCII

Supported fonts

Sans serif (single stroke and medium)

ROM-based plots

Confidence plot, DIN plot

Environment

These specifications are for the cutter without substrate.

Operating temperature

15 to 35°C (59 to 95°F)

Storage temperature

−30 to 70°C (−22 to 158°F)

Relative humidity

35 to 75%, non-condensing

TIP:

The use of dimensionally stable substrate is an essential pre-requisite to obtain high cut quality.

Additionally, substrate expansion or contraction may occur as a result of temperature variations. To improve the

dimensional stability of substrate, let it stabilize to the current environmental conditions before use, for a

minimum period of 24 hours.

Electrical

The power entry module detects the line voltage and switches automatically between 100 V and 240 V.

Input voltage

100–120/200–240 V ±10%

Input frequency

50/60 Hz

Maximum load current

2 A

Power consumption

85 VA

Fuses

T2.0A 250V

WARNING!

For continued protection against risk of fire, replace fuses only with the same type and rating of

fuse.

ENWW

Firmware

Содержание 54 Basic Cutter



























































Результаты поиска

Содержание 54 Basic Cutter

Отзывы:

HP 54 Basic Cutter, Руководство пользователя, Страница: 57 / 58

Результаты поиска

Содержание 54 Basic Cutter

Отзывы: