HP 54 Basic Cutter Скачать руководство пользователя

Страница: 21 / 58

The pinch rollers are lowered or raised simultaneously by means of the pinch roller lever arm, located on the

right-hand side of the cutter. The pinch rollers must be lifted to allow vinyl loading, during which the substrate is

fed from the rear of the cutter to the front. When raised, the pinch rollers can be moved manually to the left or

the right along the pinch roller shaft.

CAUTION:

Always make sure that the pinch rollers are fully raised before sliding them to the left or right.

CAUTION:

Always hold the assembly at the side of the pinch roller to move it from left to right. Do not

reposition the pinch roller by holding the assembly at the rear of the machine.

The pinch rollers must be positioned correctly and lowered onto the substrate before an automatic load

sequence is initiated. Make sure all the pinch rollers are positioned above a drive sleeve. The outer left pinch

roller should be positioned in one of the detents (click positions), situated under a white triangular label. The

outer right pinch roller should be positioned somewhere over the long drive sleeve. Click positions are located at

the edges of the sleeve (area marked with a white triangular label).

CAUTION:

Always leave the pinch rollers in the up position when the cutter is not in use. Leaving the pinch

rollers in the down position for a long time will create a flat spot on the pinch rollers, which will seriously degrade

tracking performance and cutting quality.

NOTE:

When the pinch rollers are raised during a job, the cutter will immediately stop and move the carriage to

the right side.

Calibrate the substrate

Substrate calibration ensures that the sensor is able to recognize the HP barcode and the markers. OPOS is

calibrated at the factory to work on a wide range of substrates. However, certain substrates—such as those with

a high gloss, or translucents—may not work with the default settings. Before working with such materials,

perform a substrate calibration. This alters OPOS’s sensitivity so that it can read the markers with greater

reliability.

Print a calibration plot on the substrate that will be used, by clicking Setup > Printer Cutter Calibration Chart in

the RIP software. Be sure to use the same ink that will be used when creating the registration markers.

ENWW

Calibrate the substrate

Содержание 54 Basic Cutter



























































Результаты поиска

Содержание 54 Basic Cutter

Отзывы:

Похожие инструкции для 54 Basic Cutter

Бренды по названию

Популярные бренды

HP 54 Basic Cutter, Руководство пользователя

Результаты поиска

Содержание 54 Basic Cutter

Отзывы:

Похожие инструкции для 54 Basic Cutter

Бренды по названию

Популярные бренды