Hozelock Pulsar Viton 5310, Инструкция по эксплуатации

Страница: 12 / 52

12
- Dosing is easy due to the graduation scale on
the reservoir. The transparent tank allows full
visibility of the liquid level.
- Preparation of the solution to be sprayed:
a) Powder product (soluble or wettable):
prepare the solution in a bucket before
decanting it into the reservoir through the filling
hole.
b) Liquid-based product (to be diluted in
water): fill the tank with 1 to 2 litres of water,
pour in the dose of liquid product, then fill up
with the required quantity of water
(Fig. 15)
.
During use
- Depending on the apparatus, manually screw the
filling cap or the pump on the reservoir
(Fig. 16)
.
- Pump to pressurise until the valve operates
(until a blast of air is released) (Fig. 17) .
- Pressurise the sprayer exclusively with its pump.
- Spray by pressing the handle switch
(Fig. 18) .
- Adjust the jet by turning the nozzle in both
directions (Fig. 19) .
- A range of accessories are available to ensure
treatments suitable for different uses (weed
control booms, telescopic lance, weed control
cover, etc.) (Fig. 14) .
See the website www.hozelock.com
After use/ Cleaning
After each use:
- Eliminate any residual pressure that may
remain in the apparatus operating the safety
valve, by pushing it, or by spraying until there is
no more pressure.
- Avoid risks of pollution by recovering any
unused product and its packaging.
- Wash your hands and face with clean water
after using the sprayer.
- Never store the sprayer pressurised.
- Never store the treatment agent inside the sprayer.
- Store the sprayer in a closed location out of the
reach of children.
- Clean the handle filter and the suction filter in
the reservoir if present in the sprayer. (Fig. 22)
- If you spray until there is just air in the spray:
eliminate residual pressure remaining in the
sprayer by operating the safety valve (Fig. 20)
or by spraying until there is no more pressure.
The residual volume of liquid is less than 250 ml.
- Before storing and before any other use
with another treatment agent, perform a
rinsing operation, i.e. put 1 litre of water into
the reservoir for dilution, mix thoroughly
and operate the apparatus to rinse all of the
apparatus' components.
This rinsing operation must be carried out
without removing any of the accessories used
during the treatment. The rinsing mixture must
not be emptied into a sewer but must be sprayed
outside on the land that has already been
treated.
- Repeat the operation several times before the
winter period.
- If there is still some unused treatment product
left, eliminate any residual pressure remaining in
the apparatus by operating the safety valve
(Fig. 20) . Recover any possible excess of product
and rinse the sprayer again as indicated above.
- Before using again, even if it is used again
immediately, with the same treatment product
or a different one, repeat the rinsing operation
3 consecutive times and check that the sprayer
works properly (especially the safety valve).
MAINTENANCE / SERVICING
Periodically, on re-use after the winter period
and several times per season, grease all the
joints (with silicone grease for sprayers) and
check that the sprayer is working properly
(especially the valve).
- Clean the nozzle and the nozzle holder
(fig. 21)
- Clean the lance filter
(fig. 22)
- Disassemble the pump (fig. 23)
- Grease or replace the valve and the seals
(fig. 23 A, B, C, D)
- The sprayer is equipped with a reservoir which
is resistant to UV radiation.
PROBLEMS / SOLUTIONS
Problems Solutions
Little or no
spraying
Make sure that all the
connectors are fully
tightened.
Make sure that all the
seals are lubricated and
clean and are not
damaged or worn.
Replace them
if necessary (contact
the customer service
department).
Clean the nozzle and the
filters.
The spraying is not
straight
Clean the nozzle.