Hozelock 3000 K7 Скачать руководство пользователя страница 7

Страница: 7 / 52

4 - DESCRIPTION (Fig.1-2)

A - Pump Body
B - Power cable (socket depending on country)
C - Carry handle
D - Outlet port
E - Coupler 1ʺ/1¼ʺ male/male
F - Nut for fitting
G - Multistage curved connector
H - High flow coupling
I - Filling cap
J- Filter
K - Water fill
L - Entry port
M - Drain cap
N - User manual
O - Switch
P - Spanner
Q - Non-return valve
R - Filter
S - Coupler 1ʺ/1ʺ male/male
T - Suction hose (7m)

5 - PREPARATION - FIRST USE

- Connection of the hoses:

Screw the male/male fitting (s) onto the inlet (L), then
the suction hose (R+S+T, Fig.3).
Screw  the  discharge  fitting  (G)  (taking  care  to  place
the flat gasket properly) using the nut provided (F).

The stepped discharge connection (G) allows (fig.4):
- The fitting of  hoses  with a diameter  25 mm  and 32

mm,

- Or the screwing of a 1” female tap nose and the

quick connection of suitable hose fittings

- Or the use of a supplied high-speed connection (H)
Cut off the end of the unused fitting (Fig.4).

- Installation: (Fig.6-7)

Before  installation  and  each  time  the  pump  is  used,
always disconnect it from the power supply.
To  avoid  accidents,  never  put  your  fingers  in  the
mouth of the pump.

Use the handle provided to transport or lift
the pump.

When  using  for  the  first  time  with  a  water  collector,
make  sure  that  the  water  collector  is  emptied  and
cleaned  of  all  accumulated  sediment,  leaves  and
debris.

-  Verify  that  the  inlet  of  the  suction  hose  is  at  least
150 mm below the surface of the water. If necessary,
retain the end of the hose with a brick. It is advisable
to  prevent  the  filter  from  touching  the  bottom  of  the
tank  (at  least  30  cm  of  water  above  the  bottom)  to
avoid sucking up any residues. It is vital that all seals
are present and that all connections are airtight.
The suction hose should not bend or kink as this may
affect its performance.
The  installation  must  comply  with  the  restrictions
related to the technical data of the pump.
- Unscrew the filler cap (I) using the supplied spanner
(P).  Fill  the  suction  chamber  via  the  filling  hole  (K)
with clean water (fig.5).

Hozelock pumps are self-priming; therefore, they can
be primed without having to fill the suction hose.

-  Connect  the  watering  hose  to  the  outlet,  ensuring
that  the  other  end  of  the  watering  hose  is  open  and
that  water  can  drain  freely  when  the  pump  is  turned
on.

- Starting up:

-  Connect  the  pump  to  a  suitable  power  supply,  and
switch on the pump using the switch (O).
- At each power up, while the suction hose is empty,
the  pump  will  start  priming.  This  operation  may  take
several  minutes.  During  the  priming,  the  pump  con-
tains a mixture of air and water, which greatly reduces
the flow and makes some noise.
- When the pump is primed and ready to be used, the
noise  level  drops,  and  the  flow  and  pressure  are
maximized.
If one of the seals or fittings is missing, or is too tight
or loose, the pump will not prime.
If  the  pump  is  not  primed  after  5  minutes  -  stop  it.
Check  the  condition  of  the  seals  and  fittings,  and
repeat the previous steps.