FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS
CAN AND MAY LEAD TO DAMAGE TO YOUR DEVICE, VOID YOUR
MANUFACTURER WARRANTY, LEAD TO PROPERTY DAMAGE, CAUSE
SERIOUS BODILY INJURY, AND CAN LEAD TO DEATH.
Before using your device, be sure to familiarize yourself with the
operating procedures.
OPERATING YOUR DEVICE
Make sure the device is fully charged before your initial use. For
charging instructions, please follow details under CHARGING
YOUR DEVICE.
Stand directly behind your device and place one foot on the
corresponding foot mat (as described in the diagram below). Keep
your weight on the foot which is still on the ground, otherwise the
device may begin to move, making it difficult to step on evenly with
your other foot. When you are ready, shift your weight to the foot
already placed on the device and step on with your second foot
quickly and evenly (as described in the diagram below).
Find your center of gravity. If your weight is distributed correctly on
the foot mats and your center of gravity is level, you should be able
to stand on your device just as if you were standing on the ground.
On average, it takes 3-5 minutes just to get comfortable standing on
your device and maintaining proper balance. Having a spotter will
BALANCE & CALIBRATION
WARNING
Overweight exertion on the device may
increase possibility of injury or product damage.
To prevent injury, when max speed is
reached, the H1 will beep to alert the user
and tilt the rider slowly back.
NOTES:
help you feel more secure. The Hover-1 is an incredibly intuitive
device; it senses even the slightest bit of motion, so having any
anxiety or reservation about stepping on may cause you to panic
and trigger unwanted movement.
When you first begin using your device, the fastest way to move in
your desired direction is to focus in that direction. You will notice
that just thinking about which way you would like to go will shift
your center of gravity, and that subtle movement will propel you in
that direction.
Your center of gravity determines which direction you move,
accelerate, decelerate, and come to a complete stop. As
described in the diagram below, tilt your center of gravity in the
direction you wish to move.
To turn, focus on the direction you wish to turn and stay relaxed.
As you get comfortable on the device, you will notice it becomes
easier to maneuver. Remember at higher speeds, it is necessary to
shift your weight to overcome the centrifugal force.
For bumps or uneven roads, bend your knees.
Dismounting your device can be one of the easiest steps, yet when
done incorrectly, may cause you to fall. To properly dismount, from a
stopped position, lift one leg up and set your foot back down on the
ground (STEPPING BACK). Then step off completely as described in
the following diagram.
WEIGHT AND SPEED LIMITATIONS
Speed and weight limits are set for your own safety. Please do not
exceed the limits listed here in the manual.
• Maximum Weight: 264 lbs
• Minimum Weight: 44 lbs
• Maximum Speed: 9 mph
OPERATING RANGE
Please notice the H1 can travel a distance up to 9 miles on a fully
charged battery in ideal conditions. The following are some of the
major factors that will affect the operating range of your device.
• Terrain: Driving distance is highest when riding on a smooth, flat
surface. Riding uphill and/or on rough terrain will reduce distance
significantly.
• Weight: A lighter user will have further range than a heavier user.
• Ambient temperature: Please ride and store the device under
recommended temperatures, which will increase driving distance;
battery life, and overall performance of your device.
• Speed and Driving Style: Maintaining a moderate and consistent
speed while riding produces maximum distance. Traveling at high
speeds for extended periods, frequent starts and stops, idling and
frequent acceleration or deceleration will decrease overall distance.
If your Hover-1 is unbalanced, vibrating, or not turning properly, you
can follow the below steps to calibrate it.
• In order for the balance calibration system to work properly, please
place the scooter on a flat, horizontal surface.
• Press and hold the ON/OFF button for a total of 15 seconds. The
scooter will turn on, lighting the battery indicator on the board.
• Next, the lights will flash. The board will then announce “calibration
successful” at which point you can release the ON/OFF button.
• Turn the board off and then turn the board back on. Calibration will
now be completed.
24
All manuals and user guides at all-guides.com
