Hoval TopGas 80 Скачать руководство пользователя страница 20

Страница: 20 / 38

4 213 894 / 01

ASSEMBLY

4.4

Flue gas connection, chimney and

condensate pipeline

NOTE

The condensate from the exhaust gas sys-

tem must not be discharged through the boi-

ler. The condensate must be discharged from

the exhaust pipe before the boiler through a

siphon.

Due to water vapour content of the flue gases with low

temperature and the resulting further condensation in the

flue, heat output boilers cannot be connected to standard

house flues.

The applicable local authority regulations and the special

regulations in the DVGW-(TRGI), ÖVGW and SVGW di-

rectives are to be complied with for flue gas removal.

In accordance with the VKF-guidelines (edition 1993,

number 3.4.8) for Switzerland a flue gas temperature li-

miting device according to the above mentioned directive

must be installed in the flue gas pipeline.

There are two possibilities of flue gas removal with heat

output gas boilers:

The use of specially approved flue gas pipelines,

Use of damp-insensitive flues, approved for flue

gas temperatures starting from 40°C, connected

to the heat output boiler in the boiler installation

room via approved flue gas pipelines.

In both cases the cross sections and maximum lengths

based on the values for flue gas flow rate, flue gas tem-

perature and flow pressure available at the flue gas con-

nector are to be calculated according to the table on page

6 (DIN 4705).

The calculation is normally made by means of graphs

or tables provided by the manufacturer of the moisture-

resistant flue of the special flue gas pipeline. Often this

manufacturer performs the calculation using a computer

program specially created for the model in question.

In any case, we recommend a discussion with the res-

ponsible local chimney sweeping supervisor prior to the

planning and execution of the flue gas extraction with

heat output gas boilers.

4.4.1 Waste gas pipelines in compliance with buil-

ding construction law

The flue gases from the Hoval TopGas

(80) can be re-

moved via a gas-tight, temperature and corrosion resis-

tant flue gas pipeline. Only flue gas systems approved

and tested by the relevant region or province are to be

connected to the Hoval TopGas

(80) (the admissions of

individual federal states should be complied with in Aus-

tria). The suppliers of the flue gas pipelines supply sui-

table boiler connectors for the transition from the boiler

to the flue gas pipeline. The flue gas connector on the

Hoval TopGas

(80) has a concentric flue gas connection

ø 100/150 mm.

We recommend installation of the connector

piece (boiler flue gas connector vertical flue

gas pipeline) in the same diameter as the flue

gas connector on the TopGas

The planning and installation instructions of the manufac-

turer together with the building construction regulations

are to be observed in the planning and execution of the

flue gas pipeline. A timely discussion with the responsible

local chimney sweeping supervisor is recommended.

Your Hoval agent can supply a suitable and approved flue

gas system for your TopGas

Please take note of the technical information supplied

with your flue gas pipeline.

4.4.2 Project planning information for the TopGas

•

All applicable regional, national and state regulations

are to be observed with respect to the flue gas extrac-

tion system.

•

All air inlet/flue gas pipelines must have a measuring

orifice (already incorporated in the moduel kits). These

are to be positioned where they can be easily accessed

for measuring purposes.

•

The concentric length elements cannot simply be shor-

tened. Length adjustment pieces or cut to length pieces

are to be used for adjusting to the required lengths.

•

Single flue gas pipes can be shortened to the necessa-

ry length but must however be cleanly deburred befo-

re the assembly, to prevent damage to the seal in the

counter-piece.

•

When installing the pipes in a shaft, spacer elements

must be mounted every 2 m. For the vertical supporting

of the chimney pipeline, the very bottom element must

be permanently fixed (mounting rail or pipe clip).

•

Horizontal connections must have a gradient of at least

5 cm per running metre in the direction of the boiler, to

permit unobstructed flow of the condensate to the boi-

ler. The complete flue gas system must be installed to

prevent the accumulation of condensate.

Содержание TopGas 80







































Результаты поиска

Содержание TopGas 80

Отзывы:

Похожие инструкции для TopGas 80

Бренды по названию

Популярные бренды

Hoval TopGas 80, Руководство по установке

Результаты поиска

Содержание TopGas 80

Отзывы:

Похожие инструкции для TopGas 80

Бренды по названию

Популярные бренды