manualshive.com logo in svg

Hoval TopGas 80, Руководство по установке, Страница: 30 / 38

Поделиться
Скачать
Hoval TopGas 80 Скачать руководство пользователя страница 30

30

4 213 894 / 01 

30

4 213 894 / 00 

MAINTENANCE

7. 

Maintenance

7.1 

Checking the water connections for leakage

Tighten  screw  connections  on  the  water  side  while  the 

boiler is still at operating temperature.

Refilling

Water must be refilled, if the water pressure falls below 

the  set  flow  pressure.  Then  allow  the  heating  water  to 

cool, bleed the filling hose and refill via the filling and drai-

ning cock.

7.2 

Maintenance includes

 

- Cleaning the flue gas heat exchanger and condensate 

collector

 

- Checking the burner

 

- Checking  the  ignition  electrode,  distance  from  burner 

approx. 4-5 mm, set position correctly where necessary 

or replace

 

-

CO

2

(O2) measuring (according to section 5.3)

7.3 

Cleaning the heat exchanger

 

- Disconnect the boiler from the electrical supply (pull out 

the plug)

 

- Close the gas appliance cock

 

- Remove the front boiler panel (open the control flap lid, 

push the front cover upwards and pull out)

 

- Disconnect the electrical connections to the gas sole-

noid valve

 

- Pull off the fan connector plug

 

- Remove mounting opening cover

 

- Unscrew the threaded of the supply pipeline to the gas 

solenoid valve (fig. 15)

 

- Remove fan

 

- Detach the screw mounted burner plate (fig. 15)

 

- Remove the burner plate and bat-wing burners (fig. 16 

und fig. 18)

 

- Wet clean the heat exchanger (do not use steel wire 

brushes) (fig. 17)

The inspection opening must be closed during 

wet cleaning

 

- Clean the condensate drain

After cleaning, assemble in reverse order. The entire gas 

way / gas route tightness check up (with leak detection 

spray) is necessary after the assembly.

7.4 

Function check

 

- Set the gas boiler according to 5.3

 

- Check all gas boiler connections for leaks

 

- Check the system pressure, replenish where necessary 

(at least 1.5 bar)

 

-

Bleed the gas boiler

 

- Complete the test record sheet

Inspection opening

fig. 14

7.5 

Emission measurement

To access the service operation menu, press ‘MODE’ and ‘+’. 

Service operation, which is carried out in heating mode, 

can be recognised by the fact that the current level alter-

nates with the characters ‘SEr’ in the display. 

When this operation mode is accessed, the burner starts 

up at 50% capacity. The output can then be varied bet-

ween 0 and 100% using the ‘+’ and ‘-’ keys.

To exit this operation mode, press the ‘RESET’ key (or the 

mode is automatically exited after 20 minutes).

Содержание TopGas 80







































Отзывы:

Нет отзывов