4
iMportaNt safetY iNstructioNs
outdoor extension Cord use
When tool is used outdoors, use only extension cords
intended for use outdoors and so marked.
additional safety precautions
Arbor and cutter should never be used as a handhold or
handle. Keep hands and clothing away from all moving parts.
Do not use Hougen Cutters where ejected slug might cause
injury (slug ejected at end of cut). Also, adhere to all
operating instructions. Do not drill through any surface that
may contain live electrical wiring.
Drilling into a live wire
could cause exposed metal parts of the drill to be made live.
Remove chips wrapped around cutter and arbor after each
hole.
With motor off and power disconnected, grasp chips
with leather gloved hand or pliers and pull while rotating
counterclockwise. Should the cutter become jammed in the
work, stop the unit immediately to prevent personal injury.
Disconnect the drill from the power supply and loosen
jammed cutter by turning the arbor counterclockwise. Never
attempt to free the jammed cutter by starting the motor.
Service at authorized repair center only.
operating near Welding equipment
Do Not
operate this unit on the same work surface that
welding is being performed on. Severe damage to the unit,
particularly the power cord, could occur. This could also result
in personal injury to the operator.
Circuit Breaker (If applicable)
Changing of the circuit breaker to a higher amp rated breaker,
or bypassing the circuit breaker is not recommended and will
void product warranty.
Circuit Breaker operation
(If applicable)
The circuit breaker is a thermal breaker. When it reaches the
higher temperature rating it will trip and cause the unit to shut
down. This is a protective device and can be reset after 5 to
10 minutes. To reset the breaker, press the breaker button
back in. If it does not reset, let the unit cool a little longer until
you can push the button in and it stays in position.
Save all warnings and instructions
for future reference.
leNGth
of corD,
feet
recoMMeNDeD
wire GauGe
recoMMeNDeD
wire GauGe
115V Motor
10 - 12 aMps
230V Motor
5 - 6 aMps
up to 25
16
18
26 - 50
14
18
51 - 100
10
16
101 - 200
8
14
201 - 300
6
12
301 - 500
4
10
d) store idle power tools out of reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools and accessories. check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect
the power tool’s operation. if damaged, have the
power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Proper
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) use the power tool, accessories and tool bits etc.
in accordance with the instructions, taking into
account the working conditions and the work to
be performed.
Use of the power till for operations
different from those intended could result in a hazard-
ous situation.
h) Keep handles and grasping surfaces, clean and
free from oil and grease.
Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5. service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
safe electrical Connection
Your Drill is rated for use on 115VAC or 230V at 50-60Hz. Do
not attempt to use drill on power sources rated other than this.
plugs and receptacles
.
Wet electrical connections are shock hazards.
To prevent the cutting fluid from traveling along
the cord and contacting the plug or power outlet,
tie a drip loop as shown. Also elevate extension
cords or gang box connections.
extension Cords
Use only 3-wire extension cords that have a 3-prong
grounding type plug and 3-pole receptacles that accept the tool’s
plug. Replace or repair damaged cords. Make sure the conductor
size is large enough to prevent excessive voltage drop which will
cause loss of power and possible motor damage.
Safe Electrical Connection
Your Mag Drill is rated for use on 115VAC or
230V at 50-60Hz. Do not attempt to use drill on
power sources rated other than this.
Extension Cords
Use only 3-wire extension cords that have 3-prong
grounding type plugs and 3-pole receptacles that
accept the tool’s plug. Replace or repair damaged
cords. Make sure the conductor size is large enough
to prevent excessive voltage drop which will cause
loss of power and possible motor damage.
Outdoor Use Extension Cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
Additional Safety Precautions
Arbor and cutter should never be used as a hand-
hold. Keep hands and clothing away from all moving
parts. Do not use Hougen Cutters where ejected slug
might cause injury (slug ejected at end of cut).
Also, adhere to all operating instructions. Do not drill
through any surface that may contain live electrical
wiring. Drilling into a live wire could cause exposed
metal parts of the drill to be made live. Remove chips
wrapped around Cutter and arbor after each hole. With
motor off and power disconnected, grasp chips with
leather gloved hand or pliers and pull while rotating
counterclockwise. Should the cutter become jammed in
the work, stop the unit immediately to prevent personal
injury. Disconnect the drill from the power supply and
loosen jammed cutter by turning the arbor counterclock-
wise. Never attempt to free the jammed cutter by starting
the motor. Service at authorized repair center only.
Extension Cord Table
Plugs and Receptacles
H
T
G
N
E
L
,
D
R
O
C
F
O
T
E
E
F
D
E
D
N
E
M
M
O
C
E
R
E
R
I
W
E
G
U
A
G
D
E
D
N
E
M
M
O
C
E
R
E
R
I
W
E
G
U
A
G
R
O
T
O
M
V
5
1
1
S
P
M
A
2
1
-
0
1
R
O
T
O
M
V
0
3
2
S
P
M
A
6
-
5
5
2
O
T
P
U
6
1
8
1
0
5
-
6
2
4
1
8
1
0
0
1
-
1
5
0
1
6
1
0
0
2
-
1
0
1
8
4
1
0
0
3
-
1
0
2
6
2
1
0
0
5
-
1
0
3
4
0
1
I
Operating Near Welding Equipment
DO NOT operate this unit on the same work surface that
welding is being performed on. Severe damage to the
unit, particularly the power cord, could occur. This could
also result in personal injury to the operator.
Circuit Breaker (If Applicable)
Changing of the circuit breaker to a higher amp rated breaker, or
bypassing the circuit breaker is not recommended and will void
product warranty.
Circuit Breaker Operation (If Applicable)
The circuit breaker is a thermal breaker. When it reaches the
higher temperature rating it will trip and cause the unit to shut
down. This is a protective device and can be reset after 5 to 10.
To reset the breaker, press the breaker button back in. If it does
not reset, let the unit cool a little longer until you can push the
button in and it stays in position.
Save these Instructions.
Important Safety Instructions - Continued
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below,
may result in electrical shock, fire and/or serious personal injury.
Typical USA 120v
Typical USA 230v
230v Type Plug
Wet electrical connections are shock hazards. To
prevent the cutting fluid from traveling along the cord
and contacting the plug or power outlet, tie a drip loop
as shown. Also elevate extension cords or gang
box connections.
Safe Electrical Connection
Your Mag Drill is rated for use on 115VAC or
230V at 50-60Hz. Do not attempt to use drill on
power sources rated other than this.
Extension Cords
Use only 3-wire extension cords that have 3-prong
grounding type plugs and 3-pole receptacles that
accept the tool’s plug. Replace or repair damaged
cords. Make sure the conductor size is large enough
to prevent excessive voltage drop which will cause
loss of power and possible motor damage.
Outdoor Use Extension Cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
Additional Safety Precautions
Arbor and cutter should never be used as a hand-
hold. Keep hands and clothing away from all moving
parts. Do not use Hougen Cutters where ejected slug
might cause injury (slug ejected at end of cut).
Also, adhere to all operating instructions. Do not drill
through any surface that may contain live electrical
wiring. Drilling into a live wire could cause exposed
metal parts of the drill to be made live. Remove chips
wrapped around Cutter and arbor after each hole. With
motor off and power disconnected, grasp chips with
leather gloved hand or pliers and pull while rotating
counterclockwise. Should the cutter become jammed in
the work, stop the unit immediately to prevent personal
injury. Disconnect the drill from the power supply and
loosen jammed cutter by turning the arbor counterclock-
wise. Never attempt to free the jammed cutter by starting
the motor. Service at authorized repair center only.
Extension Cord Table
Plugs and Receptacles
H
T
G
N
E
L
,
D
R
O
C
F
O
T
E
E
F
D
E
D
N
E
M
M
O
C
E
R
E
R
I
W
E
G
U
A
G
D
E
D
N
E
M
M
O
C
E
R
E
R
I
W
E
G
U
A
G
R
O
T
O
M
V
5
1
1
S
P
M
A
2
1
-
0
1
R
O
T
O
M
V
0
3
2
S
P
M
A
6
-
5
5
2
O
T
P
U
6
1
8
1
0
5
-
6
2
4
1
8
1
0
0
1
-
1
5
0
1
6
1
0
0
2
-
1
0
1
8
4
1
0
0
3
-
1
0
2
6
2
1
0
0
5
-
1
0
3
4
0
1
I
Operating Near Welding Equipment
DO NOT operate this unit on the same work surface that
welding is being performed on. Severe damage to the
unit, particularly the power cord, could occur. This could
also result in personal injury to the operator.
Circuit Breaker (If Applicable)
Changing of the circuit breaker to a higher amp rated breaker, or
bypassing the circuit breaker is not recommended and will void
product warranty.
Circuit Breaker Operation (If Applicable)
The circuit breaker is a thermal breaker. When it reaches the
higher temperature rating it will trip and cause the unit to shut
down. This is a protective device and can be reset after 5 to 10.
To reset the breaker, press the breaker button back in. If it does
not reset, let the unit cool a little longer until you can push the
button in and it stays in position.
Save these Instructions.
Important Safety Instructions - Continued
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below,
may result in electrical shock, fire and/or serious personal injury.
Typical USA 120v
Typical USA 230v
230v Type Plug
Wet electrical connections are shock hazards. To
prevent the cutting fluid from traveling along the cord
and contacting the plug or power outlet, tie a drip loop
as shown. Also elevate extension cords or gang
box connections.
Safe Electrical Connection
Your Mag Drill is rated for use on 115VAC or
230V at 50-60Hz. Do not attempt to use drill on
power sources rated other than this.
Extension Cords
Use only 3-wire extension cords that have 3-prong
grounding type plugs and 3-pole receptacles that
accept the tool’s plug. Replace or repair damaged
cords. Make sure the conductor size is large enough
to prevent excessive voltage drop which will cause
loss of power and possible motor damage.
Outdoor Use Extension Cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
Additional Safety Precautions
Arbor and cutter should never be used as a hand-
hold. Keep hands and clothing away from all moving
parts. Do not use Hougen Cutters where ejected slug
might cause injury (slug ejected at end of cut).
Also, adhere to all operating instructions. Do not drill
through any surface that may contain live electrical
wiring. Drilling into a live wire could cause exposed
metal parts of the drill to be made live. Remove chips
wrapped around Cutter and arbor after each hole. With
motor off and power disconnected, grasp chips with
leather gloved hand or pliers and pull while rotating
counterclockwise. Should the cutter become jammed in
the work, stop the unit immediately to prevent personal
injury. Disconnect the drill from the power supply and
loosen jammed cutter by turning the arbor counterclock-
wise. Never attempt to free the jammed cutter by starting
the motor. Service at authorized repair center only.
Extension Cord Table
Plugs and Receptacles
H
T
G
N
E
L
,
D
R
O
C
F
O
T
E
E
F
D
E
D
N
E
M
M
O
C
E
R
E
R
I
W
E
G
U
A
G
D
E
D
N
E
M
M
O
C
E
R
E
R
I
W
E
G
U
A
G
R
O
T
O
M
V
5
1
1
S
P
M
A
2
1
-
0
1
R
O
T
O
M
V
0
3
2
S
P
M
A
6
-
5
5
2
O
T
P
U
6
1
8
1
0
5
-
6
2
4
1
8
1
0
0
1
-
1
5
0
1
6
1
0
0
2
-
1
0
1
8
4
1
0
0
3
-
1
0
2
6
2
1
0
0
5
-
1
0
3
4
0
1
I
Operating Near Welding Equipment
DO NOT operate this unit on the same work surface that
welding is being performed on. Severe damage to the
unit, particularly the power cord, could occur. This could
also result in personal injury to the operator.
Circuit Breaker (If Applicable)
Changing of the circuit breaker to a higher amp rated breaker, or
bypassing the circuit breaker is not recommended and will void
product warranty.
Circuit Breaker Operation (If Applicable)
The circuit breaker is a thermal breaker. When it reaches the
higher temperature rating it will trip and cause the unit to shut
down. This is a protective device and can be reset after 5 to 10.
To reset the breaker, press the breaker button back in. If it does
not reset, let the unit cool a little longer until you can push the
button in and it stays in position.
Save these Instructions.
Important Safety Instructions - Continued
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below,
may result in electrical shock, fire and/or serious personal injury.
Typical USA 120v
Typical USA 230v
230v Type Plug
Wet electrical connections are shock hazards. To
prevent the cutting fluid from traveling along the cord
and contacting the plug or power outlet, tie a drip loop
as shown. Also elevate extension cords or gang
box connections.
Typical USA 115V
Typical USA 230V
230V Type
I
Plug
aDDitioNal safetY iNstructioNs
jjjj
