background image

Manual Hotsy, 700 Series  •  9.808-301.0 

OPERA

TOR’S MANUAL

 

 PRESSURE W

ASHER

  

6

ADVERTENCIA: Riesgo de incendio  -- No agregue 

combustible cuando el producto está en funciona-

miento o aún está caliente.
WARNING: Do not use gasoline crankcase drain-

ing or oil containing gasoline, solvents or alcohol. 

Doing so will result in fire and/or explosion.

AVERTISSEMENT: Ne pas utiliser d'essence, de 

drainage du carter de moteur ou d'essence con-

tenant de l'huile, de solvants ou de l'alcool. Agir 

de la sorte risquerait de créer un incendie et/ou 

une explosion.
ADVERTENCIA: No utilice el drenaje del cárter de 

gasolina ni aceite que contenga gasolina, solven-

tes o alcohol. Hacerlo resultará en incendio y/o 

explosión.

 7. Oil burning appliances shall be installed only in 

locations where combustible dusts and flammable 

gases or vapors are not present. Do not store or 

use gasoline near this machine.

  8.  Do not allow acids, caustic or abrasive fluids to 

pass through the pump.

 9. Never run pump dry or leave spray gun closed 

longer than 1-2 minutes.

 10. Keep operating area clear of all persons.

WARNING

USE PROTECTIVE  

EYE WEAR 

AND CLOTHING  

WHEN OPERATING 

THIS EQUIPMENT.

WARNING: High pressure spray 

can cause paint chips or other 

particles to become airborne 

and fly at high speeds. To avoid 

personal injury, eye, hand and 

foot safety devices must be 

worn.
AVERTISSEMENT: Un jet haute 

pression peut écailler 
la peinture ou provoquer 

l'émission d'autres particules dans l'air et leur 

projection à hautes vitesses. Pour éviter les lésions 

corporelles, une protection des yeux, du visage, 

des mains et des pieds doit être portée lors de 

l'utilisation de cet équipement. 
ADVERTENCIA: El rociado a alta presión pu-

ede hacer que las partículas de pintura u otras 

partículas se transporten por aire y vuelen a altas 

velocidades. Para evitar lesiones personales, se 

deben usar dispositivos de seguridad para ojos, 

manos y pies.

11. Eye, hand, and foot protection must be worn when 

using this equipment. 

(Safety glasses do not provide 

full protection.)

IMPORTANT SAFETY INFORMATION

WARNING

KEEP WATER 

SPRAY AWAY FROM 

ELECTRICAL WIRING.

WARNING: Keep wand, hose, 

and water spray away from 

electric wiring or fatal electric 

shock may result.
AVERTISSEMENT: Garder la 

lance, le boyau et le jet d'eau 

à l'écart de tout câblage élec-

trique ou des chocs électriques 

mortels pourraient survenir. 

ADVERTENCIA: Mantenga la varilla, la manguera y 

el rocío de agua lejos del cableado eléctrico, ya que 

podrían producirse descargas eléctricas fatales.

5. To protect the operator from   electrical  shock, 

the machine must be electrically grounded.  

It is the responsibility of the owner to connect this 

machine to a UL grounded receptacle of proper 

voltage and amperage ratings. Do not spray water 

on or near electrical components. Do not touch 

machine with wet hands or while standing in water. 

Always disconnect power before servicing.

RISK OF EXPLOSION: 

OPERATE ONLY WHERE 

OPEN FLAME OR 

TORCH IS PERMITTED

WARNING

WARNING: Flammable liquids 

can create fumes which can 

ignite, causing property dam-

age or severe injury.
AVERTISSEMENT: Des liquides 

inflammables peuvent produire 

des vapeurs qui peuvent 

s'enflammer, causant ainsi des 

dommages à la propriété ou des blessures graves. 

ADVERTENCIA: Los líquidos inflamables pueden 

generar vapores que pueden encenderse y causar 

daños a la propiedad o lesiones graves.
WARNING: Risk of explosion — Operate only 

where open flame or torch is permitted.

AVERTISSEMENT: Risque d'explosion —Utiliser 

uniquement dans des endroits où l'utilisation d'une 

flamme nue ou d'une torche est permise. 

ADVERTENCIA: Riesgo de explosión. Opere sólo 

donde se permitan llamas abiertas o soplete.

  6. In oil burning models, use only kerosene, No. 1 

home heating fuel, or diesel. If diesel is used, add 

a soot remover to every tankful.

WARNING:  Risk  of  fire  —  Do 

not add fuel when the product 

is operating or still hot. 
AVERTISSEMENT: Risque 

d'incendie —Ne pas ajouter 

de carburant pendant que la 

machine fonctionner ou est 

encore chaude. 

RISK OF FIRE.  

DO NOT ADD FUEL 

WHEN OPERATING 

MACHINE.

WARNING

Содержание 797SS

































Отзывы: