background image

Page 10

 

                      

ACE Salt Water Sanitizing System

NOTE: 

You may continue to use your spa as long as the chlorine level on the 

FreshWater 

®

 test strip is in the OK range.  Add granular chlorine as needed.

System Status Low (1-2):

The system status reading can be affected by cell age, scale build-up (dirty cell), cold 

water, high chlorine, dirty filters, or dirty water.

1.  Verify water temperature
 

a. 

The status reading will read lower in cooler water. To get an accurate   

 

 

status reading, ensure water is above 95° F

2.  Verify salt level 
 

a. 

Use a salt test strip to measure salt level. If the test strip shows salt    

 

 

level is low:

 

b. 

Add (1) cup of salt to the water and circulate for 5 minutes.

 

c. 

Retest with a salt test strip, and repeat until salt level reads in the OK    

   range
 

d. 

Run a manual status test to refresh. If System Status still reads low,    

 

 

check for other conditions noted above.

3.  Verify chlorine level
 

a. 

Use a 5-way test strip to measure chlorine level. If the test strip shows   

 

 

chlorine level is high (above 5 ppm):

 

b. 

Add 1 cup hydrogen peroxide with jets running. Check chlorine level    

 

 

after 10 minutes 

 

c. 

Retest with a test strip and repeat as needed

4.  Visually inspect and clean the cell
 

a. 

Follow the cell cleaning process to ensure that scale has not    

 

 

 

accumulated on the cell

 

b. 

Once the cell has been cleaned, replace the cell in the filter standpipe

 

c. 

Run a manual Status Test to refresh

5.  Visually inspect and clean filters (refer to spa owner’s manual).
6.  If the System Status message continues to read low, it may be an indication that 

it is time to replace the cell. 

System Status High (7-9):

If the Status indicator is in the red, this typically indicates that there is too much salt in 

the water. 
1.  If the status reading is less than halfway in the red:
 

a. 

Use a salt test strip to measure salt level. If the test strip shows salt    

 

 

level is high:

Содержание LIMELIGHT COLLECTION Ace





















Отзывы: