background image

Electricity Supply

STEP 1

WARNING:

The appliance must be earthed.

CE marking certifies that this appliance conforms to the following
EEC directives:
Low Voltage Equipment - 72/23/EEC & 93/68/EEC
Electromagnetic Compatibility - 89/336/EEC, 92/31/EEC & 93/68/EEC

Fuses

Your appliance comes fitted with a plug and a 13A fuse. If you need to
replace the fuse, only those rated at 13A and ASTA approved to
BS1362 should be used. To change fuse lift  holder to vertical position
and lift fuse out. To replace, insert fuse and push fuse holder down
into locked position. Correct replacement is identified by colour cod-
ing or the marking on base of plug.

WARNING: Do not use plug unless fuse holder is in locked position.

Changing the Mains Lead

A special lead can be ordered from Hotpoint Service 
UK: 08709 066 066 or 

Republic of Ireland: 1850 302 200

If you have damaged the existing lead or require a longer one a
charge will be made. It is strongly advised that this work is carried out
by a qualified electrician.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your socket.

WARNING: To avoid a shock hazard do not insert the discarded plug into
a socket anywhere else.

IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:

Green/Yellow

-

Earth

Blue -

Neutral

Brown

-

Live

If you change the plug, the colour of wires in the mains lead may not 
correspond with the colour of the markings identifying terminals in
the plug. You should therefore wire it as shown:

Green and yellow (Earth)
wire to terminal marked ‘E’,
symbol      , or coloured
green and yellow.

Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.

13A ASTA approved fuse to

BS1362.

Brown (Live) wire to terminal

marked ‘L’ or coloured red.

4

1

POLYSTYRENE BLOCK...

5

LEVEL?...

NOTE:

MOV

ALON

WHI

YOU

HOO

LEVEL

DRA

(*see 

This is part of the packaging
and should have come away
with the polystyrene base - 

IF IT HAS NOT... REMOVE IT!

NOTE: YOU MAY NEED A SECOND PERSON TO HELP YOU
RAISE AND LOWER THE APPLIANCE.

YOUR MACHINE WILL BE NOISY IF THE TWO 
NOT ADJUSTED SO THE MACHINE STANDS F
Each foot has two parts: The Locking Disk a

ii

i

Release the locking disk on the
two front feet and screw the feet
in or out until the machine stands
firm and level.

Turn ON
on the t
each is 
of the m

Locking

Disk

Foot

STEP 2

Содержание WD52













Отзывы: