GB
11
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
b) To set timer to switch on immediately and
off automatically after a set cook period
Step 1
Check that the correct time of day is set, if not follow
instructions for setting the time of day.
Step 2
Place food onto the correct shelf position in the oven
and close the oven door(s).
Step 3
Turn the oven control(s) to the required temperature,
and if necessary select the appropriate oven function.
Step 4
Press & hold in the Cook Period
button, the display will read 0.00 and
the ‘cookpot’ symbol will light up.
With the Cook Period button still held
in set the required Cook Period using
the “
+
” and “
-
” buttons.
Example: 1hr 30 minutes (as shown).
Step 5
Release all buttons.
A
U
T
O
4
1 2 0
.
The timer display will revert to the
time of day with the ‘Auto’ symbol lit
& ‘cookpot’ symbol remaining lit.
A
U
T
O
6
1 2 0
.
NOTE: The Cookpot symbol disappears
At the end of the Cook Period the ‘Auto’
symbol will flash and an intermittent
audible tone will be heard. The audible
tone will continue until cancelled. The
‘Auto’ symbol will continue to flash
until the timer is returned to Manual
operation (see below).
6
1 2 0
.
Step 6
Press the Manual button. The
audible tone will be cancelled and
the oven(s) will be returned to
Manual.
Step 7
Turn the oven control(s) to the OFF position.
To cancel an auto cooking programme
before the cook period has finished.
Step 1
Turn the oven control to the OFF position.
5
1 0 0
.
Step 2
Press the Manual button to
return the oven to “Manual” operation.
The ‘Auto’ symbol will go out.
Note 1: When cooking automatically the Cook Period
can be checked at any time by simply pressing the
Cook Period button.
Other notes on timer operation
1. When cooking Automatically the Cook Period can be
checked at any time simply by pressing the Cook Period
button.
2. When cooking Automatically the End Time can be checked
at any time by simply pressing the End Time button.
3. Having set a Cook Period and End Time an electronic
device stores the information. The device within the timer
will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake
is made, to clear:
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero’s
0.00 and ‘Auto’, it is likely that the electricity supply to
the oven has been interrupted. Reset the timer to the
correct time of day.
Food in the oven may, therefore,
not have been cooked, before serving check food is
thoroughly heated and completely cooked.
6. To set each function always press and hold the required
function button and at the same time press “
+
” or “
-
” buttons.
Hotplate
The hotplate has one dual control wok burner, one large
high speed burner, three normal simmering burners and
one small simmering burner. The dual control wok burner
consists of a smaller inner and a larger outer burner that
can operate either together or separately. Use of the two
burners together with large pans on maximum setting gives
a very high input and reduces cooking times with respect
to conventional burners. Use of the two burners together
provides a more uniform distribution of heat on the bottom
of the pan. Cookware of all sizes can be used above the
dual control wok burner. For small pans it is recommended
that only the inner burner is used.
The knob situated below the symbol
on the
fascia panel operates the outer burner.
The knob situated below the symbol
on the
fascia panel operates the inner burner.
The two normal simmering burners on the right hand side of
the hotplate are oval in form and can be turned through 90°.
This makes the hotplate more flexible in how it can be used.
For cooking fish or heating oval cookware use the two
burners with their longest sides at 90° to the front of the
hotplate.
When using the griddle or for heating rectangular, square
or large cookware use the two burners with their longest
sides parallel to the front of the hotplate.
For medium size cookware use any of the two burners in
any orientation.
All pans should be placed centrally over the burners.
TO USE THE HOTPLATE
1. Press the ignition button and then push in and turn the
control knob of the chosen burner anti-clockwise to the
large flame symbol. Continue to press the ignition button
until the spark lights the gas. When operating the dual
control burner there is a separate control knob for the
inner and outer burners.
