G
B
2
7
S
l
i
d
in
g
ra
ck k
it
asse
m
b
l
y
To assemble the sliding racks:
1. Remove the two
frames, lifting them
away from the spacers
A (
see figure
).
2. Choose which shelf to
use with the sliding rack.
Paying attention to the
direction in which the
sliding rack is to be
extracted, position joint
B and then joint C on the
frame.
3. Secure the two
frames with the guide
rails using the holes
provided on the oven
walls (
see diagram
). The
holes for the left frame
are situated at the top,
while the holes for the
right frame are at the
bottom.
4. Finally, fit the frames
on the spacers A.
Do not place the sliding racks in position 5.
A
u
to
m
ati
c c
l
eanin
g
w
it
h
t
h
e
F
A
S
T
C
L
E
A
N
f
u
n
c
tion
W
ith the FAST CLEAN mode, the internal temperature
of the oven reaches 500°C. The pyrolytic cycle is
activated and burns away food and grime residues.
Dirt is literally incinerated.
Keep children away from the appliance during the
automatic cleaning cycle as surfaces may become very
hot. Particles may ignite inside the oven due to the
spontaneous combustion process. There is no cause for
concern: this process is both normal and hazard-free.
Before initiating the FAST CLEAN mode:
Remove large or coarse food residues from inside of
the oven using a damp sponge. Do not use
detergents.
Remove all accessories.
Do not place tea towels or pot holders over the oven
handle.
If the oven is too hot, the pyrolytic cycle may not
start.
W
ait for the oven to cool down.
The programme may only be started once the oven
door has been closed.
To activate the FAST CLEAN mode, press the
button and select the desired power level (the mode
has three power levels which cannot be modified):
1.
Economy (ECO): 1 hour
2.
Normal (NOR): 1 hour and 30 minutes
3.
Intensive (INT): 2 hours.
S
a
f
et
y
devices
The door is locked automatically as soon as the
temperature exceeds a certain value.
Should a malfunction occur, the heating elements
will switch off.
Once the oven door has been locked, you cannot
change the duration and end time settings.
Programming is possible only after selecting the
FAST CLEAN mode.
Progra
mm
ing
dela
y
ed
auto
m
atic
cleaning
1. Press the
button until the
.icon and the two
digits on the TIME display flash.
2. Press the "+" and "-" buttons to adjust the hour
value.
4. Press the
button again until the other two digits
on the TIME display begin to flash.
5. Press the "+" and "-" XXX buttons to adjust the
minute value.
6. Press the
button again to confirm.
For example: it is 9:00 a.m. and the Economy (ECO)
FAST CLEAN mode level has been selected: default
set time 1 hour. 12:30 is set as the end time. The
programme will start automatically at 11:30 a.m.
Programming has been set when the
and
buttons
are illuminated. The TIME display shows the FAST
CLEAN end time and duration alternately.
To cancel a programmed procedure press the START
/
STOP button.
O
nce
t
h
e
auto
m
atic
cleaning
c
y
cle
is
over
You will have to wait until the temperature inside the
oven has cooled down sufficiently before you can open
the oven door. You will notice some white dust
deposits on the bottom and the sides of your oven;
remove these deposits with a damp sponge once the
oven has cooled down completely. Alternatively, you
can make use of the already heated oven, in which
case it is not necessary to remove the deposits, they
are completely harmless and will not affect your food in
any way.
D
B
C
Left
guide rail
Right guide
rail
Direction
of extraction
A
