4
6) When operating the unit in the pool mode, drain water from both
water tanks.
7) To end the flush cycle, press the flush button again for 5 seconds
with the dispense button off. The flush lamp goes off and
electrolyzed water is dispensed from the normal outlets indicating
normal operation.
[c] CLEANING FILTER AND SALT WATER TANK
Cap
Salt Water
Hose
Salt Water
Tank
1) Prepare a plastic bucket. Pull
out the cap, salt water hose and
filter from the salt water tank,
and put them into the bucket.
2) Wash the filter attached to the salt water hose with warm water,
and remove any dirt or dust to prevent the filter from clogging.
7. MAINTENANCE
WARNING
1. Do not splash water directly onto the unit. It may cause short
circuit, electric shock, corrosion or failure.
2. To prevent electric shock, do not touch the attachment
plug, power switch (earth leakage circuit breaker), or other
electrical parts with damp hands.
CAUTION
1. To prevent electric shock or burn, always turn off the power
switch and unplug the unit before cleaning or inspecting the
unit.
2. Do not use combustible spray or place volatile and
flammable substances near the unit. They could catch fire
from a spark of a switch or the like.
IMPORTANT
To prevent damage to the painted or plastic surfaces, do not
use the following: thinner, benzine, alcohol, petroleum, soap
powder, polishing powder, alkaline cleaner, acid, and scouring
pad. When using a chemical cloth, follow the instructions of the
manufacturer.
[a] EXTERIOR
* The exterior is powder painted. Wipe it with warm water or a neutral
cleaner, if required. Use a damp cloth to wipe off any cleaner.
* The operation panel, salt water tank, water outlets and remote
controller are made of plastic. Keep them away from impact or sharp
edges.
[b] FLUSHING CLEANING WATER PIPE
IMPORTANT
Scale such as calcium and magnesium forms inside the
cleaning water pipe. The use of the cleaning water pipe
with scale for a long period of time may prevent the flow of
cleaning water, stop the unit or cause poor performance. To
prevent scale from accumulating, flush the cleaning water pipe
periodically.
* Flush the cleaning water pipe at least once a month depending on
water quality.
1) Follow “4. START UP” and dispense electrolyzed water.
2) Open the door of the unit.
3) When operating the unit in the pool mode, drain water from both
water tanks.
4) With the dispense button off, press the flush button for 5 seconds to
light up the flush lamp. Then, press the dispense button to start a
flush cycle. During this operation, cleaning water is dispensed from
the sanitizing water outlet and sanitizing water from the cleaning
water outlet.
3) Wash the salt water tank with a neutral
cleaner to remove any salt grains or dirt.
Rinse thoroughly.
4) Wipe dry.
5) To refit the salt water hose, fit the cap on the
salt water tank, and insert the filter, then the
hose into the hole in the center of the cap.
Push in the salt water hose until the stopper
hits the cap.
Stopper
Sanitizing water from
cleaning water outlet
Cleaning water from
sanitizing water outlet
Flush Button
5)
Dispense electrolyzed water for 2 hours (flushing time may vary
depending on how bad the cleaning water pipe is clogged).
Continue to dispense electrolyzed water or use the water during
the flushing operation.
[d] CLEANING SHOWER NOZZLE (REMOTE CONTROLLER)
When clogged, remove the shower nozzle
as shown and use a toothbrush to clean the
shower holes.
Note: To prevent damage to the shower nozzle,
do not use a metal brush or knife.
[e] CHECKING WATER SOFTENER
* Check that water from the water softener is soft.
* Check that there is enough salt for refrigeration in the water softener.
* For other instructions, follow the instruction manual for the water
softener.
[f] CLEANING WATER FILTER
Remove and clean the water filter as required.
Drain Valve
Water Supply
Pipe
Water
Supply
Pressure Gauge
Shut-off Valve
Water Softener
Water Softener Assembly
Water Filter
Dual Check Valve
(accessory)
To unit
Pressure Reducing
Valve (accessory)
