In bad water conditions, a more thorough soaking may be
required. Remove the
Left Side Panel
and remove the
Float
Switch
from the
Reservoir
cover. Clean the
Float Switch
with
the solution, rinse thoroughly with clean water, and replace it back
in the cover. Follow Step
, then place a clamp on the
Reservoir
Hose
that will block the flow to the
Evaporator Assembly
. Pour
additional cleaning solution over the
Extruding Head
until the
Evaporator Assembly
is full.
Allow to soak for
10 minutes
, remove the clamp
before operation.
Otherwise, continue to Step
ව
.
Wipe down the
Infrared Sensor Lens
, (located
on the bottom of the icemaker). Rinse the lens
with a clean, damp cloth.
Move the
control switch
to
ICE
, then move the
power
switch
to
ON.
Replace the panels in their correct positions.
Make ice using the cleaning solution until it stops.
Remove the
Front Panel
. Move the
control switch
to
DRAIN
, then replace the
Front Panel
. Allow the icemaker
to drain completely.
Remove the
Front Panel
. Move the
power switch
to
OFF
. Open the water supply line shut-off valve to
supply water to the icemaker.
Move the
control switch
to
ICE
and the
power switch
to
ON
.
Allow the icemaker to fill the reservoir with water.
After the gear motor starts, move the
control
switch
to
DRAIN
. Replace the
Front Panel
.
Allow the icemaker to drain completely.
Remove the
Front Panel
. Move the
power
switch
to
OFF
. Replace the
Front Panel
. Close
the icemaker water supply line shut-off valve.
!
sanitizing continued…
x
Remove the front panel
x
Move control switch to DRAIN,
replace the front panel
x
Allow the icemaker to drain
completely
x
Remove the front panel
x
Move power switch to OFF
x
Open the icemaker water
supply line shut-off valve
x
Move control switch to ICE
x
Move power switch to ON
x
Allow the icemaker to fill the
reservoir with water
x
After the gear motor starts,
move the control switch to
DRAIN
x
Replace the front panel
x
Allow the icemaker to drain
completely
x
Remove the front panel
x
Move the control switch to ICE,
replace the front panel
x
Allow the icemaker to run for 30
minutes or produce a batch of
ice
x
Remove the front panel
x
Move the power switch to OFF
x
Pour warm water into the
dispenser/storage bin to melt
any remaining ice
x
Clean the dispenser/storage
bin liner and cover with dish
soap and a damp cloth. Rinse
thoroughly with clean water
x
Move the power switch to ON,
replace the front cover
In
re
7
W
8
M
9
R
D
10
Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
To Icemaker
Or Water Filter
OPEN
R
11
The icemaker might make a noise/squealing when first started due to scale removal from
auger/evaporator. This is normal in bad water conditions and will subside after 20
minutes.
M
A
12
Listen for
Gear Motor to Start
A
13
R
14
To Icemaker
Or Water Filter
SHUT OFF
Continue to
Sanitation – Step
༜
on front
…
භ
Air Filter/Scoop
භ
Water Filters
භ
Exterior
භ
Underside/Top Kit
භ
Icemaker/Dispenser
භ
Water Supply Inlet
භ
Extruding Head
භ
Water Hoses
Dish soap, rinse well
Check psi, change if req’d
Stainless Steel Cleaner
Dish soap & damp cloth
Follow these instructions
Clean inlet screen/valves
Inspect seal bolts/ bearing
wear. Tighten or replace
Inspect. Replace if req’d
භ
භ
භ
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
ATTENTION!
DO NOT
use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR
liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
AMMONIA
Cleaners
Tech Support: 1.800.233.1940
#51055 | 2.21.2018
Page 2
Drain
Completely
Drain
Completely
19
20
21
22
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
23
24
Page 29
