Using a nylon scouring pad, nylon brushes, and cleaning
solution scrub the
Storage Bin
,
Bin Top
†
,
Agitator
,
Drip
Ring
,
Grille
,
Spouts A & B
,
Ice Chute
, and
Drain Pan
.
†
Be sure to keep the microswitch mounted on the Bin Top dry.
Remove the clamp (if installed in Step
ල
) from the
Reservoir
hose. Rinse all parts thoroughly with clean
water before reassembling the
Drip Ring
,
Agitator
,
Bin
Top
, and
Front & Top Panels
.
Move the
control switch
to
ICE
.
Plug
the icemaker into
the electrical outlet. Move the
power switch
to
ON
.
Make ice using the cleaning solution until it stops,
dispose of ice. Move the
power switch
to
OFF
.
ATTENTION!
Icemaker might make noise/squealing when first
started due to scale being removed from auger/evaporator. This is
normal in bad water conditions and will subside after 20 min.
Cleaning Rinse:
Move the
control switch
to
DRAIN
, and the
power
switch
to
ON
. Allow the icemaker to drain completely.
Move the
power switch
to
OFF
.
Unplug
the icemaker
from the electrical outlet. Remove the
Front Panel
,
Top Panel
, and
Bin Top.
Pour clean, warm water into the ice
Storage Bin
and melt
any remaining ice. Remove
Agitator
and
Drip Ring
. Rinse
the inside of the
Storage Bin
, the
Agitator
, and
Drip Ring
thoroughly with clean water.
Pour clean, warm water over the
Extruding Head
until the
Evaporator Assembly
and the
Reservoir
are full and the
water overflows into the
Drain Pan
.
Plug
the icemaker into the electrical outlet, then move the
power switch
to
ON
. Allow the icemaker to drain
completely.
Move the
power switch
to
OFF
, then unplug the icemaker
from the electrical outlet.
Continue to
Sanitation – Step
༜
on front
...
භ
Air Filter
භ
Water Filters
භ
Exterior
භ
Pan/Gear Drain
භ
Icemaker/Dispenser
භ
Water Supply Inlet
භ
Extruding Head
භ
Water Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Clear w/ warm water + brush
Follow these instructions
Clean inlet screen/valves
Inspect seal bolts/ bearing
wear. Tighten or replace
Inspect. Replace if req’d
භ
භ
භ
Tech Support: 1.800.233.1940
#51050 | 10.06.2016
!
sanitizing continued…
x
Remove the front, top
panels, and bin top
x
Pour clean, warm water into
the ice storage bin to melt ice
x
Plug the icemaker into the
electrical outlet
x
Move
control switch
to DRAIN
x
Move
power switch
to ON
x
Allow to drain completely
x
Move
power switch
to
OFF
x
Unplug the icemaker
SANITIZE 2:
x
Repeat Steps 15–23 for
complete ice/food safety
x
Move the
control switch
to
ICE
x
Replace the front, top panels,
and bin top
x
Open the water supply line
shut-off valve, to supply
water back to the icemaker
x
Plug in the icemaker
x
Move the
power switch
to ON
x
Run icemaker for 30 minutes
x
Move the
power switch
to
OFF
x
Unplug the icemaker
x
Remove the front, top
panels, bin top, agitator,
and drip ring
x
Wipe down the ice storage bin,
bin top, agitator, drip ring, and
drain pan with a clean cloth
x
Move the
control switch
to
ICE
x
Reassemble all items, replace
all panels, and filter/louver
x
Plug in the icemaker
x
Move
power switch
to ON
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
ATTENTION!
DO NOT
use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR
liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
U
6
M
t
8
M
sw
9
M
f
10
P
11
P
12
AMMONIA
Cleaners
21
22
23
25
24
Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
R
R
7
P
13
M
f
14
Allow to Drain
Remove Front, Top
Panels, and Bin Top
Allow to Drain
ATTENTION!
ENSURE ALL COMPONENTS, FASTENERS &
THUMBSCREWS ARE SECURELY IN PLACE:
Make sure that none fall into the ice storage bin
Make ice with solution until
machine stops
Wait
1 min.
Unplug
Plug In
Unplug
Plug In
26
27
28
29
30
SCRUB
RINSE
Page 23
