Hornet 851T Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

background image

18

© 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c .

The majority of neutral safety switches can be located at the
steering column in the harness coming from the gear shift. With
the meter black lead still in the kick panel, use the red lead of the
meter to probe the suspected wires. The correct wire will show a
small amount of voltage in any gear but once the gear shift is put
in neutral or park it will read 0.00 Volts. After the correct neutral
safety wire is properly identified, solder it directly to the
BLACK/WHITE wire on the secondary connector and cover the
connection with electrical tape.

The shut down toggle switch is designed to shut the remote start

off in an emergency or to disable the remote start functions

temporarily (i.e., for service on the vehicle).

If your vehicle came with a factory neutral safety switch this

switch needs to be installed in line with the black/ white wire,

instead of soldering the black/ white wire to the factory neutral

safety wire solder the black/ white wire to one side of the switch

( it does not matter which side) and solder the other side to the

vehicle factory neutral safety switch.

important!

Do not use the vehicle until you confirm the

operation of the neutral safety feature.

«
...
19
20
21
22
23
...
»

Содержание 851T


















































Отзывы:

Нет отзывов

Похожие инструкции для 851T

Бренд: Technoline Страницы: 4

Бренд: First Alert Страницы: 5

Бренд: Salusfin Страницы: 5

Бренд: Digital Home Systems Страницы: 2

Бренд: Marksman Страницы: 28

SMOKE AND FIRE ALARM

Бренд: First Alert Страницы: 7

Бренд: First Alert Страницы: 10

Бренд: First Alert Страницы: 17

Бренд: First Alert Страницы: 5

Бренд: Fire-Lite Alarms Страницы: 2

Бренд: Fire-Lite Alarms Страницы: 4

Бренд: Fire-Lite Alarms Страницы: 4

Бренд: Fire-Lite Alarms Страницы: 48

PowerCode PC 6100

Бренд: Code Alarm Страницы: 12

Бренд: Radio Shack Страницы: 4

Бренд: DEI Страницы: 20

Бренд: Dicon Страницы: 2

Бренд: FAAST Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды