HORNER APG SmartMod HE359DIQ512 Скачать руководство пользователя страница 8

Страница: 8 / 14

MAN0922-01-EN SmarMod Quick Start Guide

____________________________________________________________________________________

Page 8 of 14 1017

14. Assemble the communications cable. Port details as per Fig 10.

Note:

These are the onboard

MJ2 connections and not
the cable connector.

Fig.10

Connect:

XLt MJ2 port (Half Duplex Mode)

SmartMod Comm. Port

Pin 1 (Tx+/Rx+)

B (D+)

Pin 2 (Tx-/Rx-)

A (D-)

Pin 6 (0V)

C (GND)

For Initialisation settings connect:

SmartMod Comm. Port

C(GND) D(INIT)

15. When the cable is assembled connect the RJ45 end to MJ2 on the XLt. Connect

the Smartmod 4-way terminal block to the HE359DIQ512 comm. port.

16. Power-up the HE359DIQ512 SmartMod. The Initialisation settings (INIT

connected to GND at power-up) will cause the SmartMod to start in the following
mode:

Baud Rate 9600, No parity, 1 Stop Bit and as Modbus Node ID 1.

This

is to allow communications so the SmartMod can be configured for alternative
settings, if necessary. See Fig. 3 above for Cscape/XLt equivalent settings.

Содержание SmartMod HE359DIQ512















Результаты поиска

Содержание SmartMod HE359DIQ512

Отзывы:

Похожие инструкции для SmartMod HE359DIQ512

Бренды по названию

Популярные бренды

HORNER APG SmartMod HE359DIQ512, Пошаговое руководство

Результаты поиска

Содержание SmartMod HE359DIQ512

Отзывы:

Похожие инструкции для SmartMod HE359DIQ512

Бренды по названию

Популярные бренды