Horizon Fitness Bookletmaker FC-200A, Руководство пользователя, Страница: 101 / 218

93
5
T
ro
uble
shootin
g
If an Icon Is Display
ed on the Error Screen /
5-1 If an Icon Is Displayed on the Error Screen
800 to 899 SPF Option Error Cause and Solution
821
Front Stitch Detection
Error
The machine did not make a front stitch.
Check if the wire has run out, or if the wire is jammed.
822
Rear Stitch Detection
Error
The machine did not make a rear stitch.
Check if the wire has run out, or if the wire is jammed.
831
Front Stitch Mis-Detec-
tion
A front stitch has detected incorrectly.
(A stitch has detected at a time independent of the sheet transportation.)
Check if the wire is mounted on the sensor, or the guide bar is too close to the sensor.
832
Rear Stitch Mis-Detec-
tion
A rear stitch has detected incorrectly.
(A stitch has detected at a time independent of the sheet transportation.)
Check if the wire is mounted on the sensor, or the guide bar is too close to the sensor.
836
Front Wire Feeding
Error
There is a problem with the wire feed.
Check if the wire has run out, or if the wire has jammed inside the stitcher head. If the
problem occurs again although the wire is OK, change the wire feeding detection set-
ting. (Refer to Section 3-5, step 4.)
Using the Administrator Mode screen, set the number of times the machine can miss
a stitch before this error is detected. (Refer to page 31.)
837 Rear Wire Feeding Error
There is a problem with the wire feed.
Check if the wire has run out, or if the wire has jammed inside the stitcher head. If the
problem occurs again although the wire is OK, change the wire feeding detection set-
ting. (Refer to Section 3-5, step 4.)
Using the Administrator Mode screen, set the number of the machine can miss a
stitch before until this error is detected. (Refer to page 31.)
900 to 999
Fore-edge Trim Section
Option Error
Cause and Solution
900
TD-200 Booklet Thick-
ness Error
A thickness error has been detected and the operation stopped immediately. Check
the booklet thickness.
1100 to 1199 SPF Section System Error Cause and Solution
1100 Interlock Contactor Fault There is a problem with the interlock contactor K00. Please call your local dealer.
1101 Inverter Alarm
Turn off the power switch, wait about 10 minutes, then turn it on again.
If the problem occurs again, please call your local dealer.
1102
Body Pulse Detection
Error
Check if the body of the machine moves forward or backward when you press the
body forward/backward movement motor M02 on the Information-Single Operation
screen. If the body does not move, fuse F02 may be blown. Replace the fuse. (Refer
to Section 6-11.) If the fuse is OK, please call your local dealer.
The binding operation can be continued temporarily by changing the installation posi-
tion of the machine.
1103
Electrical Box Cooling
Fan 1 Alarm
Cooling fan M03 is not turning. Please call your local dealer.
1104
Electrical Box Cooling
Fan 2 Alarm
Cooling fan M04 is not turning. Please call your local dealer.
1120 Stitching Motor Alarm
The stitching motor driver A20 (SPF) has produced an error.
Turn off the power switch, wait about 10 minutes, then turn it on again.
If the problem occurs again, check if circuit breaker Q20 is tripped. If Q20 is tripped,
turn it on again. If the breaker is OK, please call your local dealer.
1140 Folding On/Off Error
Sheets have been transported to the fold section although the job does not require
folding, or sheets have been transported to the horizontal transport section although
the job requires folding. Please call your local dealer.
1141
Fold Knife Operation
Error
Although the fold knife should move, the fold knife home position sensor keeps turn-
ing on so the fold knife does not move.
1151
Transport Pulse (Infeed
Section) Detect Error
Check if circuit breaker Q01 is tripped. If Q01 is tripped, turn it on again. If the breaker
is OK, please call your local dealer.
1152
Transport Pulse (Deliv-
ery Section) Detect Error
Check if circuit breaker Q01 is tripped. If Q01 is tripped, turn it on again. If the breaker
is OK, please call your local dealer.
1170
Stitching Motor Opera-
tion Error
The machine did not verify that the stitching operation was done and the stitcher was
raised to the upper limit.
The stitching motor ran but the stitching operation did not finish correctly. Please call
your local dealer.
1198
Downstream Device
Power Down while
Operation The power for a downstream device was turned off while the machine was trying to operate.
Check the connector on the left side of the SPF-200A/200L. (Refer to Section 1-2-2.)
If the connector is connected correctly, please call your local dealer.
1199
Downstream Device Not
Connected/Interlock Dis-
connection Error
Check the downstream device is connected to the SPF-200A/200L correctly, or the
downstream device is powered on.
If the delivery conveyor is used as a downstream device, check if the short circuit
connector for stand-alone use is connected. (Refer to Section 1-2-2.)
If the problem occurs again, please call your local dealer.