3
METHODS OF USE FOR STEAM CLEANER
1. Make sure desired cleaning accessories (Jet Nozzle, Utility Brush, and Utility Head
with window squeegee) are properly connected.
2. For general cleaning convenience, Extension Pole should be removed so that unit
functions as a handheld steam cleaner. However, Extension Pole may be attached
for cleaning hard-to-reach spots, such as floor grout or ceilings. BE CAREFUL TO
SUPPORT EXTENSION POLE WITH TWO HANDS WHEN LIFTING.
3. Follow General operating instructions to begin steaming.
4. Selecting Steam Settings guidelines to choose the steam intensity setting appropriate
for the surface you are cleaning.
5. Direct Jet Nozzle towards surface you wish to steam. Use a slight back-and-forth
motion over area to enhance the cleaning process. To sanitize surfaces, set Steam
Control Dial to HIGH and hold Jet Nozzle approximately 1CM from surface for at
least 5 seconds. This will most effectively kill germs and bacteria.
6. When using Window Squeegee, start by thoroughly steaming entire window or
mirror, then turn steam off. Next, press Window Squeegee to top of window or
mirror, and pull slowly downward. Move slowly from one side of the surface to the
other in this fashion until entire surface is clean.
7. Wipe steamed areas with a clean cloth to remove loosened dirt and grime. Wiping
the area while it is still wet is recommended, but use caution when wiping surfaces
such as metal that may still be hot.
JET NOZZLE [10]
1. Can concentrate the steam to remove spot stain from cloth.
2. If you need to remove dirty spots from cloth, please turn the Steam Control Dial to
high and forward the nozzle to the spot from the distance of 1CM.
UTILITY BRUSHES [11]
Utility Brushes are to be installed on the jet nozzle.
WINDOW SqUEEGEE AND UTILITY HEAD [12]
The Window squeegee is to be installed on the Utility Head before installing on the Steam
nozzle of main body and is used for cleaning windows, mirrors and other smooth glass
surfaces.
The Utility Head with Small Cloth is to be used for removing wrinkles from different
fabrics. Choose the steam intensity setting appropriate for the fabric you are steaming.
EXTENSION HOSE [13]
You can install either the Jet Nozzle or Utility Head on the Extension Hose and install the
Extension Hose on the Steam nozzle of main body for extensive reach and lighter weight
while using as handheld steam cleaner.
GB
3. Carefully fill Measuring Cup with maximum amount of water 450 ml and pour into
Water Tank through the fill hole.
DO NOT
Exceed the “MAX” water line on the water tank.
NOTE:
In order to significantly reduce mineral build-up and prolong the life of your steam
mop the use of distilled or de-mineralized water in the unit is highly recommended.
4. Replace Water Tank Cap so that thread grooves on the bottom of Cap align with tabs
inside fill hole. Press Water Tank Cap down so that it sits flush with top of fill hole.
Rotate one quarter turn in clockwise direction (as indicated by “Lock” illustration on
Cap) to lock it in place.
NOTE:
The tube which transfers water from the Water Tank to the boiler is
weighted down with a brass ball. This is an intentional design to improve efficiency
of water usage. It is normal for this ball to create a rattling sound inside of Water
Tank during use.
GENERAL OPERATION
NOTE: Be sure that the Water Tank has been filled and all desired
accessories are connected before following these steps.
1. Plug power cord into a convenient electrical outlet (a properly rated
extension cord may be used if necessary).
2. Turn Steam Control Dial clockwise from “OFF” to “MAX”, Power light will illuminate
in red.
[9]
NOTE:
The desired steam intensity setting depends on the current steaming task.
3. After approximately 30 seconds, the indicator light in blue color will be illuminate &
you will hear a buzzing sound as unit begins to emit steam.
4. Direct Steam Nozzle (with any connected accessories) towards surface you wish to
steam.
CAUTION:
Always be sure that Steam Nozzle and any accessories are pointed in a safe
direction (away from yourself, other people, pets and plants) when steam is being emitted.
METHODS OF USE FOR STEAM MOP
Please inspect carefully if the Extension Pole, Mop Head and Micro-fiber Mop Pad are
assembled correctly.
1. Use a steady back-and-forth motion over the floor, pushing Mop away and pulling
it back towards you. Work your way backwards over the floor, in order to avoid
walking over the freshly mopped area.
2. The Mop Pad will absorb dirt and moisture during mopping. However, depending on
floor
surface and steam intensity setting some residual moisture may be left behind.
In this case, it is recommended to allow floor time to air-dry. A fan may be directed
towards mopped area to facilitate faster drying.
NOTE:
To avoid warping or damage caused by heat and moisture, the steam mop should
only be used on properly sealed floor surfaces. Always test on a small area of your flooring
prior to overall use on every floor surface.
