User Manual
XYR301E Wireless Ethernet
34-XY-25-41
Page 33
To resume normal configured operation when Configuration is complete, switch Factory Default dip-switch on the
XYR301-E to RUN and cycle power.
Note
:
Security Certificates
. Configuration of the XYR301-E uses an encrypted link (https). The security certificate
used by the XYR301-E is issued by HONEYWELL and matches the IP address 192.168.0.100.
When you first connect to the XYR301-E, your web browser will issue a warning that HONEYWELL is not a trusted
authority. Ignore this warning and proceed to the configuration web page.
Internet Explorer 7 has an additional address check on security certificates. Unless the XYR301-E has the address
192.168.0.100, when you first connect to the XYR301-E, Internet Explorer 7 will issue a warning about mismatched
security certificate address. You can turn off this behaviour in IE7 by selecting
“Tools > Internet Options > Advanced > Security > Warn about certificate address mismatch*”
Method 2 - Set XYR301-E Network address to match the local network
For this method you will need to determine what IP address, Gateway address, and netmask to assign to the XYR301-E
so that it appears on your network. Ask your system administrator if you don’t know the correct settings for your
network. E.g.
The default IP address of the XYR301-E modem is 192.168.0.1 and the network you wish to connect to is on
10.10.0.X (PC is on 10.10.0.5)
Once you have determined the correct settings for your network, you need to connect to the modem’s RS-232 serial
port using a straight through serial cable and a terminal package such as Hyperterminal set to 115,200 baud. 8 data bits,
1 stop bit, no Parity.
Open Hyperterminal and monitor communications
Set the SETUP/RUN switch to the SETUP position, and connect power to the modem.
Observe Hyperterminal and when you see the Dragon screen (see below) press <Enter> to get the following
prompt “#”
Type the following “ifconfig” and it will show the configuration of the Ethernet port and from this you will be able
to see what the IP address is, e.g.
eth0 Link encap:Ethernet HWaddr 00:12:AF:FF:FF:FF
inet addr:
192.168.0.1
Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU: 1500 Metric: 1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:256
Temporarily change the IP address to something that will enable connection to your local network. E.g type
“ifconfig eth0 10.10.0.6 netmask 255.255.255.0” only add the netmask if the netmask is anything other than the
standard 255.255.255.0
IP address should now be changed and you can check by typing “ifconfig” again. Note these changes are only
temporary and if the module is reset they will go back to the normal default (192.168.0.XXX).
Open Internet Explorer and ensure that settings will allow you to connect to the IP address selected. If the PC uses
a proxy server, ensure that Internet Explorer will bypass the Proxy Server for local addresses. This option may be
modified by opening Tools -> Internet Options -> Connections Tab -> LAN Settings->Proxy Server -> bypass
proxy for local addresses.
_ __,----'~~~~~~~~~`-----.__
. . `//====- ____,-'~`
-. \_|// . /||\\ `~~~~`---.___./
______-==. _-~o `\/ ||| \\ _,'`
__,--' ,=='||\=_ ;_,_,/ _-'|- |`\ \\ ,'
_-' ,=' | \\`. '',/~7 /- / || `\. /
.' ,' | \\ \_ " / /- / || \ /
/ _____ / | \\.`-_/ /|- _/ ,|| \ /
,-' `-|--'~~`--_ \ `==-/ `| \'--===-' _/`
' `-| /| )-'\~' _,--"'
'-~^\_/ | | `\_ ,^ /\
/ \ \__ \/~ `\__
_,-' _/'\ ,-'~____-'`-/ ``===\
((->/' \|||' `. `\. , _||
\_ `\ `~---|__i__i__\--~'_/
__-^-_ `) \-.______________,-~'
///,-'~`__--^- |-------~~~~^'
///,--~`-\
Содержание XYR301E
Страница 2: ...Page ii April 2012 ...
Страница 18: ......
