manualshive.com logo in svg

Honeywell VR8405, Руководство пользователя, Страница: 7 / 12

Поделиться
Скачать
Honeywell VR8405 Скачать руководство пользователя страница 7

7

68-0150

VR8405

INSTALLATION  •  STARTUP AND CHECKOUT

Fig. 7—VR8405 wiring connection in S89C Direct Ignition System.

24V

24V (GND)

VALVE
VALVE (GND)

L2

HSI

L1

HSI

MVPV

MVPV

L1
(HOT)

L2

1

3

2

1

2

3

3

VR8405
COMBINATION
GAS CONTROL

S89/S890 HOT SURFACE 
IGNITER CONTROL

HOT SURFACE
IGNITER/SENSOR

Q354 FLAME
SENSOR

LIMIT 
CONTROLLER

THERMOSTAT OR
CONTROLLER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
MAKE SURE L1 AND L2 ARE NOT REVERSED. THIS WOULD PREVENT FLAME DETECTION.

ALTERNATE LIMIT CONTROLLER LOCATION

SEN TERMINAL AND Q354 FLAME SENSOR ON D MODELS ONLY.

SEN

BURNER 
GROUND

M8054

QUICK 
CONNECTS

Startup and Checkout

PERFORM GAS LEAK TEST

WARNING

FIRE OR EXPLOSION HAZARD
CAN CAUSE PROPERTY DAMAGE,
SEVERE INJURY, OR DEATH.
Check for gas leaks with a rich soap and water
solution any time work is done on a gas control.

GAS LEAK TEST

1. Paint all pipe connections upstream of the gas control

with a rich soap and water solution. Bubbles indicate a gas
leak.

2. If a gas leak is detected, tighten the pipe connection.
3. Stand clear while lighting main burner to prevent

injury caused from hidden gas leaks that could cause flash-
back in the appliance vestibule. Turn on the entire gas
control and light the main burner as described below.

4. With the main burner in operation, paint all pipe

joints and gas control inlet and outlet with a rich soap and
water solution.

5. If another gas leak is detected, tighten pipe connections.
6. Replace the part if gas leak cannot be stopped.

WARNING

FIRE OR EXPLOSION HAZARD
CAN CAUSE PROPERTY DAMAGE,
SEVERE INJURY, OR DEATH.
1. Do not force the gas control knobs. Use only

your hand to turn the gas control knobs. Never
use any tools.

2. If the gas control knobs will not operate by

hand, call a qualified service technician to re-
place the entire gas control.

3. Both knobs must be in the same position for

operation or shutoff.

GAS CONTROL KNOBS SETTINGS

The gas control knobs have two settings:
OFF: Prevents main burner gas flow.
ON: Permits gas to flow into the control body. Under

control of the thermostat and direct ignition module,
gas can flow to the main burner.

NOTE: Gas controls are shipped with the gas control knobs

in the ON position.

Содержание VR8405













Отзывы:

Нет отзывов