Honeywell VR8304 Скачать руководство пользователя

Страница: 11 / 14

The VR8300 gas controls provide ON-OFF manual

control of gas flow. In the OFF position, pilot and main

burner gas flow is prevented. In the ON position, pilot and

main burner gas flow is under control of the thermostat, the

intermittent pilot module, and the two automatic main

valves.

SYSTEM OPERATION WITH S8600

When the thermostat calls for heat, the S8600 Inter

mittent Pilot Module is energized. The S8600, in turn,

activates the first automatic valve of the gas control. Pilot

gas flow is allowed. Simultaneously, the S8600 module

generates a spark at the igniter-sensor and lights the pilot.

The pilot flame is sensed by the igniter-sensor, and spark

generation ends.

After the pilot is lit, the S8600 module energizes the

solenoid for the second automatic valve operator and gas

flow main burner is followed (the first automatic valve

remains energized). The second automatic valve dia-

phragm, controlled by the servo pressure regulator, opens

and adjusts gas flow as long as the system is powered and

the pilot is burning. The servo pressure regulator monitors

outlet pressure to provide an even main burner gas flow.

Loss of power (thermostat satisfied) de-energizes the

S8600 module and closes both automatic valves. The

system is ready to return to normal service when power is

restored through the thermostat.

Loss of pilot flame, or flame too small to reliably light

main burner, closes the second automatic valve operator.

The S8600 module then attempts to restart pilot. On S8600

modules with lockout timers, the first automatic valve

closes after the lockout period. On S8600 modules without

lockout timers, the trial for ignition continues indefinitely

and the first automatic valve remains open.

H pilot flame is restarted successfully, main burner is

reopened, and gas flows to main burner as described

above. Gas control operation is described in more detail

below.

SECOND

AUTOMATIC

SERVO

/ PRESSURE

REGULATOR

NOTE, SECOND AUTOMATIC VALVE OPERATOR AND SERVO PRESSURE REGULATOR

SHOWN OUTSIDE GAS CONTROL FOR EASE IN TRACING GAS FLOW.

SLOW-OPENING GAS CONTROL HAS A GAS FLOW RESTRICTOR IN THIS PASSAGE.

12,3958

FIG. 11-POSITION OF GAS CONTROL COMPONENTS DURING THERMOSTAT OFF CYCLE.

68-0108-1

Содержание VR8304















Результаты поиска

Содержание VR8304

Отзывы:

Похожие инструкции для VR8304

Бренды по названию

Популярные бренды

Honeywell VR8304, Руководство пользователя

Результаты поиска

Содержание VR8304

Отзывы:

Похожие инструкции для VR8304

Бренды по названию

Популярные бренды