Honeywell VISIONPRO TB8220U Скачать руководство пользователя страница 8

TB8220U COMMERCIAL VISIONPRO™ PROGRAMMABLE THERMOSTAT

62-3070—07

8

POWER THE THERMOSTAT

You can choose from three methods to power the 
thermostat:
• Batteries only (AAA alkaline).
• 24 Vac direct connection only.
• 24 Vac direct connection with battery backup (AAA 

alkaline).

Wiring 24 Vac Common

• Single-Transformer System—Connect the common 

side of the transformer to the C screw terminal of the 
thermostat wallplate. Leave the metal jumper wire in 
place between Rc and R.

• Two-Transformer System—Connect the common side 

of the cooling transformer to the C screw terminal of 
the thermostat wallplate. Remove the metal jumper 
wire between Rc and R.

Installing Batteries

1.

Install three AAA alkaline batteries on the back of 
the thermostat as marked. See Fig. 22.

Fig. 22. Installing batteries.

2.

Locate and remove the tab labeled Remove. See 
Fig. 23.

IMPORTANT

This tab must be removed in order to set the 
real-time clock.

Fig. 23. Remove tab labeled REMOVE from 

thermostat back.

Setting Calendar and Time

Setting Calendar

This thermostat is designed to, under normal use, 
automatically keep current time and day in memory for up 
to ten years once the calendar is set. There are two ways 
to set the calendar for this thermostat:

SETTING CALENDAR WHEN THERMOSTAT IS FIRST 
POWERED

When the thermostat is first powered, the display is ready 
to set the calendar and time. The thermostat proceeds 
through a sequence of setup screens. See Fig. 24.

SETTING CALENDAR AFTER THERMOSTAT IS 
ALREADY FUNCTIONING

See steps 1 through 4, in the Advanced Settings section, 
to set year, month and day.

Fig. 24. Setting calendar and time after initial powerup.

Mount Thermostat to Wallplate

1.

Align the terminal screw blocks with the pins on the 
back of the thermostat.

2.

Push the thermostat straight onto the wallplate until 
it snaps into place. See Fig. 25.

M19918

BATTERIES (3)

REMOVE DURING INSTALLATION

M19920

REMOVE  

TAB

REMOVE DURING INSTALLATION

DONE

MON

MON

TUE

WED

WED

THU

THU

FRI

FRI

SSAA

SUN

CHANGE FILTER UV LAMP HUMIDIFIER PAD

OK TO PICK MULTIPLE DAYS    SCREEN LOCKED

DONE

MON

MON

WED

WED

THU

THU

FRI

FRI

SSAA

SUN

PM

CHANGE FILTER UV LAMP HUMIDIFIER PAD

OK TO PICK MULTIPLE DAYS    SCREEN LOCKED

SET CURRENT DAY

SET MONTH

USE ARROWS TO SET YEAR AND TIME

M22761

Содержание VISIONPRO TB8220U

















Отзывы: