background image

10

11

9

8

If there is still no communication, please perform the

following steps:

• Bring the main unit and remote sensor close together. 

• Remove four (4) small screws from the back of the

remote sensor with a small Phillips screwdriver, and

open the battery compartment. 

• Remove the batteries from the battery compartment

and reinstall them in the same manner. Remote sensor

LED indicator will flash showing transmission of the

signal. 

• Remove the batteries from the main unit and reinstall

them in the same manner. 

• The remote temperature appearing on the main unit’s

display will show that the transmission is being

received successfully.

TRANSMISSION COLLISION

Signals from other household devices such as wireless

doorbells, home security systems, and entry control

may interfere with this product or cause temporary

reception interruption. This is normal and will not affect

the general performance of the product. The

transmission and reception of the temperature readings

will resume once the interference subsides.

PRECAUTIONS

This product is engineered to give you years of satisfactory

service if handled carefully. Here are a few precautions:

•  Do not immerse the units in water.

•  Do not clean the units with abrasive or corrosive

materials. They may scratch the plastic parts and 

corrode the electronic circuits.

•  Do not subject the product to excessive force, shock, 

dust, temperature, or humidity, which may result in

malfunctions, shorter lifespan, damaged batteries, and

damaged parts.

•  Do not tamper with the units internal components. 

Doing so will invalidate the warranty and may cause

damage. These units contain no user-serviceable parts.

NOTE: 

When the temperature falls below freezing, the

batteries in the outdoor remote sensor may have

reduced voltage supply and a shorter effective range.

We recommend using lithium batteries at temperatures

of 32

°

F (0

°

C) and below.

BATTERY INSTALLATION

REMOTE SENSOR

NOTE: Install the batteries; select the channel and

temperature in C

°

 or F

°

 before mounting the

remote sensor.

• Remove the screws from the battery compartment

with a small Phillips screwdriver.

• Set the channel. The switch is located in the battery

compartment. Channel 1 is typically selected if only

one remote sensor is being used.

• Install 2 “AA” size alkaline batteries (not included)

matching the polarities shown in the battery compartment.

• Replace the battery compartment door and secure the

screws.

• Secure the remote sensor in the desired location.

MAIN UNIT

• Open the battery compartment door.

• Install 2 batteries (UM-3 or “AA” size 1.5V) matching

the polarity as shown in the battery compartment.

• Replace the battery compartment door.

LOW BATTERY WARNING

A low-battery indicator [    ] will appear on the indoor

or remote temperature reading line of the main unit

warning that the corresponding batteries need replacement.

The Unit is in searching mode

Temperature readings are 

securely registered

No signals detected.

GETTING STARTED

After batteries are installed; remote sensor will transmit

temperature readings at 45 second intervals. The main

unit may take up to two minutes to receive the initial

readings. Upon successful reception, remote temperature

will appear on the larger section of the main unit’s

display (the default remote channel is channel one). The

main unit will automatically update readings at 

45-second intervals.

If no signal is received from the remote sensor within

two minutes, dashes [- - -] will be displayed. Press and

hold the 

SEARCH

 button on the main unit for two

seconds to initiate another signal search.

CHECKING REMOTE AND INDOOR

TEMPERATURE

The remote temperature information is

located on the larger section of the

main unit’s display. 

The wave icon is located above the

remote channel number and indicates

the reception status from the remote

sensor. 

There are three types of reception

status that may be displayed:

The indoor temperature with the icon 

IN

 is located

next to the remote temperature information section.

NOTE:

 If the indoor or remote temperature goes above

or below operating range stated in specifications, the

main unit’s display will show dashes “- - -”

MAXIMUM AND MINIMUM READINGS

The maximum and minimum record of the indoor and

remote temperatures will be automatically stored in

the memory of the main unit (receiver). 

To display the minimum, maximum

or the current reading, press the

MEM

 button.

If no button is pressed for the next 15 seconds, the

unit will return to the current temperature display.

To clear the memory, press and hold the M

EM

 button

for two seconds and all previously stored readings

will be erased.

LOST COMMUNICATION

If the main unit display line for the remote sensor

reading goes blank, press and hold the 

SEARCH

button for 2 seconds to begin a new signal search.

If the signal still isn’t received, please make sure that: 

• The remote sensor is in its proper location.

• The distance between main unit and remote sensor

is not over 100 feet (30meters). 

• The path between units is clear of obstacles. Shorten

the distance if necessary.

• Fresh batteries are installed correctly in both remote

sensor and main unit. 

Содержание TM004

Страница 1: ...Remote Sensor This device displays and monitors temperature from up to three remote locations from the comfort of your home In this package you will find One main unit receiver One remote sensor transmitter TS03C One User Manual Please keep this manual handy as you use your new item It contains practical step by step instructions as well as technical specifications and precautions you should know ...

Страница 2: ...furniture 4 Though the remote sensors are weather resistant they should be placed away from direct sunlight rain or snow E WALL MOUNT RECESSED HOLE Keeps the main unit on the wall F C F BUTTON Selects temperature display in Celsius or Fahrenheit G BATTERY COMPARTMENT Accommodates 2 two UM 3 or AA 1 5V alkaline batteries FRONT VIEW A TEMPERATURE INFORMATION IN A TWO SECTION LCD DISPLAY B CHANNEL BU...

Страница 3: ...he desired location MAIN UNIT Open the battery compartment door Install 2 batteries UM 3 or AA size 1 5V matching the polarity as shown in the battery compartment Replace the battery compartment door LOW BATTERY WARNING A low battery indicator will appear on the indoor or remote temperature reading line of the main unit warning that the corresponding batteries need replacement The Unit is in searc...

Страница 4: ...wing measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help DECLARATION OF CONFORMITY We Name Hideki Electronics Inc Address 7865 SW Mohawk Tualatin OR 97062 Telephone No 1 ...

Отзывы: