Honeywell SUPER TRADELINE S8610U Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

Honeywell SUPER TRADELINE S8610U Скачать руководство пользователя страница 17

S8610U UNIVERSAL INTERMITTENT PILOT GAS IGNITION CONTROL

17

69-1955

Failed Trial for Pilot Ignition

The S8610U control module provides multiple trials for
ignition (TFI). If the pilot is not lit or sensed before the end
of the trial for ignition time, the ignition control shuts off
the spark and pilot gas (100% shutoff). There is a five
minute delay before another TFI is initiated. The pattern of
TFI followed by a five minute delay continues until the

pilot lights and is proved or the “Call for Heat” ends. The
five minute delay time can be bypassed by cycling the
system thermostat or removing and restoring system
power.

The following operating sequence includes vent damper
operation (if connected) and Prepurge (if configured).

Fig. 8. Normal Operating Sequence.

OPERATING SEQUENCE

“CALL FOR HEAT”

RECEIVED FROM

THERMOSTAT

POWER TO

MODULE AND

SELF CHECK

IDLE

(NOT POWERED)

RUN

YES

TRIAL FOR

IGNITION

(TIMER STARTED)

SPARK ON

OPEN PILOT GAS

VALVE

FLAME

PROVED?

FLAME

STABILIZATION

(2 SECONDS)

YES

NO

RETRY

OPEN MAIN GAS

VALVE

CLOSE MAIN GAS

VALVE AND PILOT

GAS VALVE

FLAME

LOST?

NO

CLOSE PILOT

GAS VALVE

SPARK OFF

“CALL

FOR HEAT”

ENDS?

YES

NO

RETRY DELAY

(5 MINUTES)

SPARK OFF

A

B

MORE THAN

5 FLAME LOSSES

IN THIS “CALL

FOR HEAT”?

YES

(BEFORE TRIAL FOR IGNITION TIMER EXPIRES)

A

CLOSE MAIN GAS

VALVE AND PILOT

GAS VALVE

M23588

IF CONFIGURED,

BEGIN PREPURGE

(30 SECONDS)

DAMPER

CONNECTED?

DE-ENERGIZE

(CLOSE) DAMPER

DAMPER SWITCH

OPENS IN 60 SEC.?

1

IF DAMPER CONNECTED AND DAMPER SWITCH IS OPEN, IGNITION CONTROL CLOSES PILOT

AND MAIN GAS VALVES (IF OPEN), TURNS SPARK OFF (IF ON), AND GOES TO CHECK STATUS

OF DAMPER SWITCH.

CHECK STATUS

OF DAMPER SWITCH

YES

YES

NO

NO

DAMPER SWITCH

CLOSES IN 60 SEC.?

YES

NO

1

1

1

1

NO

1

B

«
...
15
16
17
18
19
...
»

Содержание SUPER TRADELINE S8610U

























Отзывы:

Нет отзывов