Honeywell SmartPAC 2 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 522

Honeywell SmartPAC 2 Скачать руководство пользователя страница 91

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 69

Part 4 – Install and Wire SmartPAC

SmartPAC 2 the First Step—Checking the Press, next section

Installing SmartPAC 2 Enclosure, page 70

Installing SmartPAC 2 as a Panel Mount, page 72

Wiring between WPC and SmartPAC, page 74

Connecting AC Wiring Between

WPC and SmartPAC 2, page 76

Connect Stop Circuits and Input Check Circuit to SmartPAC 277

Connecting SmartPAC 2 to a Network, page 79

SmartPAC 2 the First Step—Checking the Press

DANGER

!

ELECTRIC SHOCK OR HAZARDOUS ENERGY

•

Disconnect main power before installation.

•

Remove all power to the press, press control, and other equipment used with the press.

•

Remove all fuses and “tag out” per OSHA 1910.147 Control of Hazardous Energy (Lockout/
Tagout).

•

Ensure that Installation is performed by qualified personnel.

•

Complete all wiring installation procedures before connecting to the AC power source.

Failure to comply with these instructions will result in death or serious injury.

NOTICE

UPGRADING FROM ORIGINAL SMARTPAC

See “Appendix E – Upgrade from Original SmartPAC,” page 457 for instructions on
upgrading from original SmartPAC to SmartPAC 2.

NOTICE

MOVE RAM TO TDC BEFORE INSTALLING SMARTPAC 2

This is an important step because the press

must

be at top dead center (TDC) when you

make final adjustments for the resolver. Be accurate when setting the press to TDC. Set to
0° ±2°.

Use a dial indicator on the face of the ram if necessary

.

Before starting the installation, remove the die from the press. Then

check all modes of

press operation

. Run the press in INCH, SINGLE STROKE, and CONTINUOUS modes.

Make sure the press has working top stop and emergency stop circuits. Verification that the
press operates and stops properly is extremely important because SmartPAC 2 will be tied in
to the press stop circuits. Do not forget to mark your electrical prints where you wire in
SmartPAC 2. Set the press ram to top dead center (TDC).

«
...
89
90
91
92
93
...
»

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов