manualshive.com logo in svg

Honeywell SmartPAC 2, Руководство пользователя, Страница: 101 / 522

Поделиться
Скачать
Honeywell SmartPAC 2 Скачать руководство пользователя страница 101

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 79

11. Make all the necessary conduit connections to ensure NEMA 12 protection.

SmartPAC 2 is rated NEMA 12 (protected against dust and oil).  

Be sure to label all

wires in a way consistent with your press’s electrical prints.

Connecting SmartPAC 2 to a Network

Before you can connect SmartPAC 2 to a computer network, your network administrator
must make the necessary connections and settings.

The Ethernet cable plugs into the Ethernet connector on the SmartPAC 2 PC board (see
Figure 2 - 39, page 162,).

NOTICE

SETTING STATIC IP ADDRESS

SmartPAC 2 comes from the factory set up for a Dynamic Host Configuration Protocol
(DHCP) network, which automatically assigns IP addresses.  If your network requires static
IP addresses, have your network administrator contact Wintriss Tech Support for assistance
in setting up SmartPAC 2 with a static IP address. See also “CHANGE NETWORK
SETTINGS” in the Initialization chapter, page 262.

Содержание SmartPAC 2











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов