Honeywell Notifier VESDA-E VEA Series Скачать руководство пользователя | Manualshive

Страница: 3 / 10

background image

VEA Product Guide —

P/N LS10215-000NF-E:A 07/24/2018

3

Wiring

The terminal block for SLC wiring will accept wire sizes from 24 AWG – 12 AWG. Route the SLC wiring through the cabling inlets located on the
upper and lower sides of the detector base and terminate the wiring on to the respective terminals on the SLC terminal block, as shown in figure
below.

Refer to the diagram below to wire the SLC detector to the FACP.

Communication ports

All of the standard ports of VEA-040-Axx are available except for VESDAnet. VESDAnet is not available to the user in these models of the detec-
tors. However Gateway function is still applicable to this detector model to connect to Xtralis VSC.

SLC Connections

To next
device

Terminal Block on

the Interface module

FACP

SLC +

SLC -

+ + - -

«
1
2
3
4
5
...
»

Содержание Notifier VESDA-E VEA Series











Отзывы:

Нет отзывов

Похожие инструкции для Notifier VESDA-E VEA Series

INSAFE+Origin D731D

Бренд: Nexelec Страницы: 34

Бренд: CYCLOPS Страницы: 8

Бренд: System Sensor Страницы: 4

Uniguard Superflow UG-5-AFR Series

Бренд: CALECTRO Страницы: 4

Бренд: LST Страницы: 1

Бренд: Directed Electronics Страницы: 20

Бренд: Braun Страницы: 4

Бренд: SOUNDMASTER Страницы: 61

Бренд: NUTRICHEF Страницы: 6

Бренд: CrimeStopper Страницы: 32

Бренд: FONRI Страницы: 132

Бренд: Halo Страницы: 8

Бренд: Masterbuilt Страницы: 6

Бренд: Eurochron Страницы: 4

Pursuit PRO9233Z

Бренд: Voxx Electronics Страницы: 8

Бренд: Capehart Страницы: 5

Бренд: brennenstuhl Страницы: 55

Бренд: System Sensor Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды