Honeywell NOTIFIER IDR-M, Руководство по установке и пусконаладке

Страница: 15 / 24

IDR-M Mimic Installation & Commissioning Manual
Installation Guide
12 997-412-000-3, Issue 3
June 2005
2.5.1.2 Control Board
The connections to this board are shown below.
Switch Configuration - RS485 Connection
Set the switches (located at position A):
a. Switches 1 to 6 set the IDR-M mimic
address, in the range 1 to 31 in binary (see
decode at left; switch 6 is always set to 0).
If all these switches are set to 0, there are
two possible conditions:
i A soft address can be set by the IDR
Configuration Tool. See the instructions
supplied with the Tool.
ii If no soft address is set, the hard address
is 0 (‘listen only’) which must only be used
during commissioning.
Note: If used with an ID50 panel, only
addresses 1 to 16 are valid.
b. Switch 7 must be set according to the type
of connection used by the mimic , in this
case 0 for RS485 (does not have to be the
same as in (c) below).
c. Set switch 8 according to the type of
network used by the fire panel ; set to 0 if
an RS485 network (i.e. Master/Slave) is
used, or to 1 if an ID
2 net network is used.
Ensure that the IDR-Mimic
does not share an address
with a repeater, and that the
address matches that
configured in the fire control
panel
Address Switch settings (1=on)
1 2 3 4 5 6
1 1 0 0 0 0 0
2 0 1 0 0 0 0
3 1 1 0 0 0 0
4 0 0 1 0 0 0
5 1 0 1 0 0 0
6 0 1 1 0 0 0
7 1 1 1 0 0 0
8 0 0 0 1 0 0
9 1 0 0 1 0 0
10 0 1 0 1 0 0
11 1 1 0 1 0 0
12 0 0 1 1 0 0
13 1 0 1 1 0 0
14 0 1 1 1 0 0
15 1 1 1 1 0 0
16 0 0 0 0 1 0
17 1 0 0 0 1 0
18 0 1 0 0 1 0
19 1 1 0 0 1 0
20 0 0 1 0 1 0
21 1 0 1 0 1 0
22 0 1 1 0 1 0
23 1 1 1 0 1 0
24 0 0 0 1 1 0
25 1 0 0 1 1 0
26 0 1 0 1 1 0
27 1 1 0 1 1 0
28 0 0 1 1 1 0
29 1 0 1 1 1 0
30 0 1 1 1 1 0
31 1 1 1 1 1 0
Connection
to Termination
board
Connection to Mimic
Driver board
(SPI Bus)
A B
No
connection
C
Processor reset
switch
No
connection
No
connection
No
connection
No
connection
No
connection
No
connection
No
connection
No
connection
Termination
Resistance
Termination
Resistance
IDR-M MIMIC IDR-M MIMIC IDR-M MIMIC IDR-M MIMIC IDR-M MIMIC IDR-M MIMIC
FIRE CONTROL PANEL FIRE CONTROL PANEL
EXAMPLE MASTER/SLAVE NETWORK CONFIGURATION EXAMPLE MASTER/SLAVE NETWORK CONFIGURATION
0V 0V 0V 0V
B A
24V 24V 24V 24V
B A
B A
AUX 24V AUX 24V
B B A
IN OUT
A
Termination
Resistance
Termination
Resistance