manualshive.com logo in svg

Honeywell NOTIFIER AM-8000, Руководство по установке, Страница: 12 / 35

Поделиться
Скачать
Honeywell NOTIFIER AM-8000 Скачать руководство пользователя страница 12

AM-8000 

Manuale di installazione 

PAGE - 9 

AM8000_manu-inst 

  Doc. 160.1-AM8000-ITA Rev A.3 

NOTIFIER ITALIA 

Current consumption from battery  

  Current from battery in 

Normal Condition

 in the absence of mains voltage 230Vac: 

 

 

CPU-8000

 Card at nominal voltage (24Vdc): 83mA if the Card is connected to LCD-8000-L (or LCD-

8000-F); 91mA if the Card is not connected to LCD. 

 

 

1x LIB-8000

 at nominal voltage (24Vdc): 67mA 

 

 

LCD-8000-L

 at nominal voltage (24Vdc) and backlight low: 111mA if the LCD is connected to the CPU-

8000 Card; 148mA if LCD have remote connection (by CAN-LCD-8000 adaptor) 

 

LCD-8000-F

 at nominal voltage (24Vdc) and backlight low: 178mA if the LCD is connected to the 

CPU-8000 Card; 236mA if LCD have remote connection (by CAN-LCD-8000 adaptor)

 

  + external loads

 

  Current from battery 

in Alarm Condition 

in the absence of mains voltage 230 Vac:

 

 

CPU-8000

 Card at nominal voltage (24Vdc): 100mA with LCD-8000-L (or LCD-8000-F) connected 

on-board; 108mA LCD not connected 

 

 

1x LIB-8000

 at nominal voltage (24Vdc): 75mA 

 

 

LCD-8000-L

 at nominal voltage (24Vdc) and full backlight : 169mA if the LCD is connected to the CPU-

8000 Card;  218mA if LCD have remote connection (by CAN-LCD-8000 adaptor) 

 

LCD-8000-F 

at nominal voltage (24Vdc) and full backlight : 215mA if the LCD is connected to the CPU-

8000 Card;  274mA if LCD have remote connection (by CAN-LCD-8000 adaptor) 

  + external loads

 

 

See the appendix at the end of this manual for proper battery calculation in Stand-by and in Alarm 
condition. 

 

User power supply output

 

 

The AM-8000 control unit has one 24 Vdc 

fixed output 

 

The output is protected by 4 A FAST fuse 
Use the fixed voltage output to power 

external loads such as, for example, LCD 
repeaters displays. 

 

User Sounder Output: 

 28 Vdc + 3% - 17%, max ripple 500mV 

 3,5A (the sum of the current MUST NOT 

EXCEED THE MAXIMUM CURRENT 
available from the power supply) 

 
 

  

 
 
 
Fuse list 

 

230 V mains voltage

  

3,15 AL  

Battery Output

 

7 A RESETTABLE 

User power supply output      

 

4 A RESETTABLE 

Sounder output                           

 

1,35 A RESETTABLE 

 

 

 

User power supply output connection 

(refer to basic board topography) 

            CNU

 

 

GND

24V 

01 02

 

Содержание NOTIFIER AM-8000




































Отзывы:

Нет отзывов