manualshive.com logo in svg

Honeywell LC13-510, Руководство пользователя, Страница: 46 / 76

Поделиться
Скачать
Honeywell LC13-510 Скачать руководство пользователя страница 46

Dual Node Module Service

3-10

9/95

3.3.6

3.3.6  EPNI Board

NOTE

                                          The EPNI board is a later version of the PNI board.

The EPNI board is a controller board which interfaces the bus and processor in a similar
way as the controller boards listed in subsection 3.3.2.  First, check the 

SELF TST/ERR

light (red - should be out) and 

PASS MOD TEST

 light (green - should be on) on the EPNI

board.

The 

SELF TST/ERR

 light (red) is driven by a microprocessor on the EPNI board.  If it is

on, check for the following causes:

•

There was a hardware failure on the EPNI board.

•

A problem was detected on-line (for instance, there may have been an EPNI local
RAM parity error or a duplicate address may have been detected).

•

The node was shut down (stunned) due to a watchdog timeout.

•

The number of raw errors detected exceeded a preset threshold, causing the
software on the EPNI board to enter the failed state.

If the state of the 

SELF TST/ERR

 light and 

PASS MOD TEST

 light are correct, continue with

this instruction.  Under normal system operating conditions, the following indicators and
connections are present on the EPNI board:

•

Red LEDs

 are out.

•

Green LED

 is on.

•

The TX yellow LED

 either blinks on and off (indicating traffic) or stays on (heavy

traffic).

Check that there are no disconnected or broken cables.  If part of the UCN has failed, the
failure reporting and diagnostic tests included in the software will help isolate the problem.

Содержание LC13-510













































































Отзывы:

Нет отзывов