manualshive.com logo in svg

Honeywell HERMetic UTImeter Gtex Chem, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Honeywell HERMetic UTImeter Gtex Chem Скачать руководство пользователя страница 42

42 

www.tanksystem.com

10.5  Sensing probe replacement

THE REPLACEMENT OF THE SENSING PROBE DOES  
NOT REQUIRE TO RE-CALIBRATE THE TEMPERATURE 
NOR THE ULLAGE / INTERFACE.

10.5.1  Disconnecting the old sensing probe

•   Unscrew the securing screw with the 1.5 mm Hex Allen  

key. 

•   Pull carefully the adaptor out of the sensing probe tube by 

turning it slightly left and right. Make sure that the O-ring is  
not damaged when it passes the hole of the sensing probe 
tube.

•   Disconnect the plug by pulling it gently out of the tube.

10.5.2  Connecting the new sensing probe

•   Refer to Figure 10-9.
•   Insert the 1.5 Allen key gently in the free hole in the middle  

of the tape plug.

•   With one hand keep the sensing probe and the tape adaptor 

as shown on Figure 10-9.

•   With the other hand drive the plug into the new sensor tube 

with the 1.5 Allen key to connect it to the sensing probe 
socket. Note this is a one way only plug. The wires shall be  
on the opposite side of the electronic circuit print as shown  
on Figure 10-9.

•   Pull out gently the 1.5 Allen key from the plug while keeping 

the plug in place with another non sharp tool, for instance  
the 4 mm Allen key. Check that the plug is fully inserted.

•   Switch on the unit and wait a few seconds. If all is OK, 

the temperature is displayed and the buzzer beeps every 
2 seconds. If there is any problem, refer to the section 11 
“Trouble shooting”.

•   Put some light grease on the O-ring.
•   Push gently the adaptor into the sensing probe tube.  

Mind not to damage the O-ring when it passes the screw 
hole.

•   Screw the securing screw back with the 1.5 mm Hex Allen 

key.

10.6  Tape wipers replacement

The 2 tape wipers can be easily replaced:

•   Check that the tape cleaner is on “DOWN” position.
•   Unlock and remove the housing lid.
•   The tape wipers are inserted in holders grooves. Remove  

the old ones and insert the new ones.

•   Put back and lock the housing lid
•   Check that the tape cleaner is working properly.

Note:

 we recommend to change always both wipers.

1.5 mm Allen key

one-way only plug

thread for securing screw

sensor tube

tape wires

O-ring

tape adaptor

tape

Figure 10-9

wipers

Figure 10-10

Содержание HERMetic UTImeter Gtex Chem













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды