manualshive.com logo in svg

Honeywell Gent Vigilon Compact, Руководство по эксплуатации

Поделиться
Скачать
Honeywell Gent Vigilon Compact Скачать руководство пользователя страница 39

Maintenance

Replacing the glass on a Manual Call
Point

a.

Disengage the front cover from the call point
assembly using the end of the test key. Insert
the key into the slots 'E' and from the bottom
edge lift out the cover.

b.

Carefully remove broken glass.

&

Take appropriate

precautions when clearing broken
glass to prevent injury.

c.

Turn the test key such that the tab is at position
'F' and insert a new glass as shown.

d.

Hook the front cover onto the top edge of the
call point assembly and then push the bottom
edge down until it click shuts. Check both hooks
on the top of the front cover are locked onto the
call point assembly.

e.

Turn the test key anticlockwise one quarter of a
turn such that the glass is held under the yellow
arm.

S4-34891 Spare MCP glass (Pack of 10)

Resetting the resettable element on a
Manual Call Point

Slide the cover upwards to expose the key hole. Insert
the test key in the keyhole and turn it clockwise by
one quarter of a turn. Then turn the test key
anticlockwise by one quarter of a turn to reset the call
point element.

39

Vigilon

COMPACT VOICE ALARM

E

F

GLASS

YELLOW
ARM

Test Key

Cover

Содержание Gent Vigilon Compact













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды