Application
Loop Cards
(VIG-LPC-EN and COMPACT-LPC-EN)
4188-1075 issue 3_Part 1_08/14
1
The Loop Cards (VIG-LPC-EN and COMPACT-LPC-EN) are for use in Vigilon and Vigilon Compact panels. The Cards
can be identified by the
‘SEC-GEN LOOP CARD’ marking along the long edge on the component side of the PCB. There should
also be a
firmware version number label on the PCB, ensure the version requirements are met.
How to select a Loop card, MCC/MCB Card and PSU for
typical device mix found on sites:
a) Choose a selection method.
b) Use the information below to find a solution for a site.
S4 range of products
S3 mark 1/2
Up to 2Km loop
Typical loop device mix found on sites
S4 and 34000 of products
Up to 1Km loop
S3 mark 1/2
S4 range of products
S3 mark 1/2
Up to 1Km loop
S3 mark 1
34000 range of products
Up to 1Km loop
2
1
5
6
2
1
2
Vigilon Fire System
GENT 2012
Designed to EN54 Pt
2 & 4
Healthy
15:45
Fault
System Fault
Test
Fire
Power
Power Fault
CB254
Disablement
Sounder
1 2 3 4 5
6 7 8 9
10 11 12 13 14
15 16
17 18 19 20 21
22 23 24 25
26 27 28 29 30
30 32
Zones
Previous
Next
Delay
Verify
CB253
EN Vigilon 4/6 loop panel
(VIG1-24 or VIG1-72)
2
A
B
C
D
E
Typically the Compact panel based systems use
devices
shown in
site scenarios , and .
T
s
A
B
C
S4 range of products
Part 23 compliant
Up to 2Km loop
2014
S3 mark 3 VAD
Pt23 compliant
S4 Interfaces
S4 Interfaces
S4 Interfaces
34000
Interfaces
2
1
S4 Interfaces
Vigilon Panels
EN Compact panel
(COMPACT-24)
1
Legacy secnarios
2
1
2
1
L
o
op car
d
, MC
C/MCB and
PSU c
ombina
tions
VAD is a ‘Visual Alarm Device’.
The Loop card (VIG-LPC-EN or COMPACT-LPC-EN) must never be
used in a Vigilon panel based System having device mix with
3400 sensors .
T
3
Post March 2014
build of
EN Compact Loop card
(COMPACT-LPC-EN)
V4.48 or higher
MCB
1
2
V4.52 or higher
Post March 2014
build of EN Vigilon
Loop card
(VIG-LPC-EN)
V4.48 or higher
Pre or Post July 2013
Vigilon PSU
(VS-PSU-24) or
(VS-PSU-72)
A
B
or
will require
Post July 13
PSU
V4.52 or higher
MCC
B C D
E
A
B C D
E
A
Selection Method 1
a) Select a panel
b) Select applicable cards and PSU build
c) Determine which site device mix will work,
eg: or ---- etc.
For example:
If we have an EN Vigilon 4/6 loop panel
(VIG-24) having Cards shown in then
it will work with site device
mix , , , or .
B
D
A
2
B
D
A
E
C
Selection Method 2
a) Select a site device mix, eg or ---- etc.
b) Note the number in circle.
c) Match the number in circle with cards and
panels.
For example:
If a site has device mix is installed on a 2Km
loop and you want to an EN Vigilon Compact
panel (COMPACT-24) then Cards
shown in must be built into the panel
B
D
A
B
1
See note
S
ee caution
S
ee caution
A 1Km or 2km loop length is the sum the length of cable used on
the main loop and spur circuits off the main loop, on which
system devices are connected.
Selection Method 3
a) Match the number in circle.
For example:
Panel will work with
Cards when used in site with
Device mix .
1
1
1
S4 S4
S4
Future scenario
New scenario
Current scenario
Selection
S4 with VAD
Pt23 com
S4 sensor sounders
and S4 sensors
34000 and 3400 range
of products
Up to 1km loop
S3 mark 1
34410 Fire Alarm Zone Module
F
34000
Interfaces
3400
F
