manualshive.com logo in svg

Honeywell EC7823A, Руководство по установке, Страница: 7 / 8

Поделиться
Скачать
Honeywell EC7823A Скачать руководство пользователя страница 7

EC7823A;RM7823A 7800 SERIES RELAY MODULES

7

66-1086—2

OPERATION

Sequence of Operation

The EC/RM7823A has the following operating sequences, 

see Fig.4 and Table 5. The EC/RM7823A LED provide 

positive visual indication of the program sequence: POWER, 

FLAME and ALARM.

Fig. 4. Sequence status LEDs.

Table 5. LED sequence status display information.

Standby

The EC/RM7823A is ready to respond to sensing of a flame or 

flame simulating condition. The green POWER LED blinks 

every four seconds, indicating that the relay module is doing 

internal hardware checks. 

Run

The EC/RM7823A pulls in the internal dpdt relay and turns on 

the FLAME LED when a flame or flame simulating condition 

exists. The relay module is now in the Run sequence.

Static Checkout

After checking all wiring, perform this checkout before 

installing the EC/RM7823A on the subbase. These tests verify 

the Q7800 Wiring Subbase is wired correctly, and the external 

controllers, limits, interlocks, actuators, valves, transformers, 

motors and other devices are operating properly. 

WARNING

Explosion and/or Electrical Shock Hazard.

Can cause serious injury, death or equipment 

damage.

1. Close all manual fuel shutoff valve(s) before starting 

these tests. 

2. Use extreme care while testing the system. Line 

voltage is present on most terminal connections 

when power is on.

3. Open the master switch before installing or 

removing a jumper on the subbase. 

4. Before continuing to the next test, be sure to 

remove test jumper(s) used in the previous test. 

5. Replace all limits and interlocks that are not 

operating properly. Do not bypass limits and 

interlocks.

CAUTION

Equipment Damage Hazard.

Improper testing will cause serious internal 

damage.

Do not perform a dielectric test with the EC/RM7823A 

installed. Internal surge protectors can break down 

and conduct a current. This can cause the 

EC/RM7823A to fail the dielectric test or possibly 

destroy the internal lightning and high current 

protection. 

Equipment Recommended

1.

Voltmeter (1M ohm/volt minimum sensitivity) set on the 

0 to 300 Vac scale. 

2.

Two jumper wires, no. 14 wire, insulated, 12 in. 

(305 mm) long with insulated alligator clips at both ends. 

Burner Sequence

LED Energized

Standby

POWER

, FLAME and ALARM.

Run

POWER, FLAME

 and ALARM.

Reset/Alarm Test

POWER

, FLAME and 

ALARM

.

CAPTIVE 

MOUNTING 

SCREW

DUST

COVER

RELAY 

MODULE

FLAME

AMPLIFIER

RESET PUSHBUTTON

SEQUENCE

STATUS

LEDS

M7889

Содержание EC7823A









Отзывы:

Нет отзывов