Honeywell CP-300E Series Скачать руководство пользователя страница 8

WEB-300E, WEB-600E/U, CP-300E, CP-600E/U SERIES CONTROLLERS

31-00010—01

8

If desired, you can use the wall mount NPB-WPM-US/U in 

your office (to initially commission the controller), and then 

install the controller at the job using either a NPB-PWR-H/

U or NPB-PWR-UN-H/U module. The following sections 

provide more details:

• “NPB-PWR-H/U” on page 8 (24 Vac/dc-powered in-line 

module)

• “NPB-PWR-UN-H/U” on page 8 (Universal 120V–

240Vac-powered in-line module)

• “NPB-WPM-US/U (Wall Mount AC Adapter)” on page 9 

NPB-PWR-H/U

Use the NPB-PWR-H/U module to power the controller 

(and if installed, IO-16-H/U modules) from a dedicated 

Class 2, 24Vac transformer, or from a 24Vdc power 

supply.

NOTE: If there is no optional NiMH backup battery, 

using the NPB-PWR-H/U allows a higher 

operating temperature. See “Environmental 

Requirements” on page 3.

NOTE: If powering from a 24V transformer, do not 

power any other equipment with it. Other-

wise, conducted noise problems may result. 

Also, do not ground either side of the trans-

former’s 24V secondary.

Fig. 4. NPB-PWR-H/U module wiring connections.

Located at the bottom of the NPB-PWR-H/U module is a 

2-position power connector, and an earth ground spade 

lug, as shown in Fig. 4.

Connect the supplied earth ground wire to a nearby earth 

ground point. Unplug the power connector plug from the 

module and make connections to it as shown.

CAUTION

Do not plug 24V power into the NPB-PWR-H/U 

(reinsert connector plug) until all other 

mounting and wiring is completed. See “Initial 

power up and checkout.” on page 12.

NPB-PWR-UN-H/U

The NPB-PWR-UN-H/U module lets you power the 

controller (and if installed, connected I/O modules) from 

AC line power, with a universal input range from 120–

240Vac. If installing IO-16-H/U modules, the NPB-PWR-

UN-H/U module mounts as the last (end) module in the 

chain. (See Fig. 1 on page 4).

WARNING

• A 120Vac or 240Vac circuit powers the NPB-

PWR-UN-H/U. Disconnect power to this circuit 

before installation to prevent electrical shock 

or equipment damage.

• Make all connections in accordance with 

national and local electrical codes. Use copper 

conductors only.

• Do not exceed the 30W capacity of NPB-

PWR-UN-H/U by the powered devices.

+

M34991

CONTROLLER

NPB-PWR-H/U (COVER REMOVED)

EARTH GROUND

SUPPLIED EARTH 

GROUNDING WIRE

DEDICATED 24VAC TRANSFORMER

NEITHER SIDE OF SECONDARY 

TIED TO EARTH GROUND

24VAC

OR

24VDC

24VDC POWER SUPPLY

(POLARITY NOT CRITICAL) 

NEITHER SIDE TIED TO EARTH

Содержание CP-300E Series





















Отзывы: