manualshive.com logo in svg

Honeywell CP-300E Series, Руководство по установке, Страница: 17 / 20

Поделиться
Скачать
Honeywell CP-300E Series Скачать руководство пользователя страница 17

WEB-300E, WEB-600E/U, CP-300E, CP-600E/U SERIES CONTROLLERS

17

31-00010—01

8.

Check the RS-485 biasing jumpers on the existing 

unit, and duplicate on the replacement unit (See 

“Disassembling the controller.” on page 11.)

9.

Mount the replacement controller as it was previ-

ously, using the same DIN rail location and/or 

screws.

10.

Reconnect/remount any removed accessory mod-

ules, being careful to replace in the same order, 

using the same DIN rail location and/or screws. 

Secure all modules as done previously.

11.

Reconnect the earth ground wire to the controller’s 

grounding lug and any installed accessory modules.

12.

Reconnect any Ethernet, serial, modem, and I/O 

connectors.

13.

If using IO modules, and any of your I/O points have 

voltage, turn the devices back on, or reconnect 

power to them.

14.

Replace the cover. See “Removing and Replacing 

the Cover” on page 4.

15.

Restore power to the unit. It should boot up as a 

new unit (See “Check the Status LED” on page 12.).

16.

Using the WEBs-AX platform tools, re-commission 

the controller, and install the saved station data-

base. For more details, see the

 JACE WEBs-AX 

Install and Startup Guide.

Returning a Defective Unit

For proper credit on an in-warranty unit, ship the defective 

unit per the vendor’s return material procedures.

NOTE: If the defective unit is under warranty, please 

follow return instructions provided in this 

section.

If the unit is out of warranty, please discard 

any replaced part. Do not return an out-of-

warranty  controller.

Prior to returning the unit, contact your vendor to obtain a 

return materials authorization (RMA) number and other 

instructions.

Please provide:
• Product model

• Serial number

• Nature of the defect

• PO number to secure the RMA

CERTIFICATIONS

The WEB/CP-300E and WEB/CP-600E/U controller each 

has the following agency listings, compliances, and 

certifications:

• UL 916 - Underwriters Laboratories, Energy 

Management Device, CAN/CSA C22.2 Canadian 

Safety Standards

• FCC Part 15, Class B - Federal Communications 

Commission

• ICES-003, Class B - Industry Canada Interference-

Causing Equipment Standard

• EU 202/95/EC RoHS (Restriction of Hazardous 

Substances)

• CE Declaration of Conformity (Council Directive 004-

108-EC)

For complete details on listings and compliances for these 

controllers, refer to the document 

Agency Listings and 

Approvals for Tridium Hardware Products

.

TAB MOUNTING DIMENSIONS

Measurements are in inches and (mm). Note that DIN 

mounting is recommended over tab mounting. See Fig. 1 

on page 4.

Содержание CP-300E Series





















Отзывы:

Нет отзывов