manualshive.com logo in svg

Honeywell CP-300E Series, Руководство по установке, Страница: 15 / 20

Поделиться
Скачать
Honeywell CP-300E Series Скачать руководство пользователя страница 15

WEB-300E, WEB-600E/U, CP-300E, CP-600E/U SERIES CONTROLLERS

15

31-00010—01

Fig. 9. Optional NiMH battery pack in WEB/CP-300E or WEB/CP-600E/U controller.

CAUTION

Use only NiMH battery packs approved for use 

with the controller.

Installing/replacing WEB/CP-300E 

or WEB/CP-600E/U series 

controller NiMH battery assembly.

1.

If replacing an existing battery in a controller not 

currently configured for SRAM usage, backup the 

controller’s configuration to your PC using the 

appropriate WEBs-AX software tool (for example, 

Workbench).

2.

If a station is running, stop it using the platform 

Application Director view.

3.

Remove all power from the controller. Wait for all 

LED activity to stop (if a battery is already installed, 

this may take a minute or two).

4.

Remove the cover. See “Removing and Replacing 

the Cover” on page 4. Note the Option Slot area 

where the NiMH battery assembly mounts.

5.

If a battery assembly is already mounted, unplug 

the battery from the connector on the controller 

board (see Fig. 9).

6.

Remove the four screws that secure both option slot 

end plates (and if installed, the existing battery 

assembly bracket). Set the screws aside. 

Remove any existing battery assembly (if applica-

ble).

7.

Plug the battery connector plug of the new battery 

assembly into the battery connector on the control-

ler (see Fig. 9).

8.

Set the new NiMH battery assembly on top of the 

option card slots, over the option card end plates. 

Ensure the bracket mounting holes are aligned with 

the standoffs. 

9.

Place the four screws through the battery bracket, 

option card end plates, and into the standoffs on the 

controller’s base board. Using a screwdriver, hand 

tighten these screws.

10.

Replace the cover. 

11.

Restore power to the controller and verify normal 

operation.

Battery maintenance

Battery life expectancy is a function of its discharge cycles 

(the number of discharges and their depth) and the 

ambient temperature of the battery during normal 

operation. In most applications, the NiMH battery should 

see relatively few discharges. Therefore, ambient 

temperature has more to do  with the life expectancy of 

the battery than does any other factor. If the controller is 

installed in a conditioned space, this battery should 

provide dependable service for approximately three years 

(average). In an environment where the operating 

temperature reaches the highest range (50 ºC or 122 ºF), 

you should only expect the battery to last around one 

year.

A new NiMH battery is typically only partially charged 

when shipped. Additionally, NiMH batteries lose charge 

over time if not kept trickle-charged (for more details, see 

“NiMH battery pack” on page 13). Therefore, even a new 

or replacement battery will require up to 18 hours of 

powered operation before it can provide reliable backup 

power (is at full charge).

The controller monitors the NiMH battery and periodically 

loads the battery to test its ability to maintain battery-

backed functions. Investigate any battery trouble 

message, and check the battery connections to the unit. 

Replace the battery as required. To order a new battery, 

see “Standard Replacement Parts” on page 16.

Battery disposal

Please dispose of the used NiMH battery in accordance 

with local, state, and federal regulations.

M34988

NiMH BATTERY 

CONNECTOR ON 

CONTROLLER 

BOARD

CONTROLLER

WITH COVER

REMOVED

MOUNTING 

SCREWS (4)

INSTALLED NiMH 

BATTERY ASSEMBLY

NiMH BATTERY 

PLUGGED INTO

CONNECTOR ON

CONTROLLER

BRACKET PART

OF ASSEMBLY

OPTIONAL NiMH 

BATTERY ASSEMBLY

(NPB-BATTERY/U)

Содержание CP-300E Series





















Отзывы:

Нет отзывов