manualshive.com logo in svg

Honeywell AQS51, Руководство по установке, Страница: 5 / 8

Поделиться
Скачать
Honeywell AQS51 Скачать руководство пользователя страница 5

AQS 51/61 CO2 / TEMPERATURE SENSOR WITH BUILT-IN CONTROLLER

EN1B-0189GE51 R0102

5

Maintenance Level

A number of execution options are available from the

MAINTENANCE MENU (see Table 4). This level is accessed

only from the display mode in the OUT1 % selection. Simul-

taneously pressing two push buttons restricts access,

intended for competent trained service personnel only (see

Fig. 7). The ENTER command is issued by simultaneously

pressing MENU and ESC.

Always use the ESC button to return to the MENU selection

block in the left-hand portion of Fig. 7. Several pushes of the

ESC button may be needed to return to the DEFAULT mode.

The ENTER command (press MENU and ESC simultaneous-

ly) may result in the execution of functions with temporary or

permanent changes to parameters affecting sensor/controller

outputs and system operation.

Table 4. Maintenance functions available on the AQS61

Function

line

Display

Time limit

1

Functional description

1

FOUt

no

For checking/adjusting connected auxiliary equipment.

Provides access to a sub-menu in which output selection XX = 1...4 is done by pressing

MENU. The selected output FOXX (= OUT1-4) is fixed via ENTER

2

. For XX=1,2  LO always

provides 2 V /4 mA regardless of the position of the start point selection jumper, but

voltage or current according to the position of the jumper. OFF/ON is true for the relay and

open collector outputs.

FO 1,2 LO:

selected output is fixed to 2V / 4 mA

FO 3

LO:

relay contact is open

FO 4

LO:

OUT4 is 0V/open state

FOXX

HI:

selected output is fixed to 10V/20mA/closed state

2

bCAL

yes

CO

2

-sensor calibration with fresh air. An easy way to correct a zero-point error of a sensor.

The sensor needs fresh air (380...420 ppm CO

2

). The calibration must be confirmed by

pushing ENTER

3

CAL

yes

Zero-point calibration of the CO

2

 sensor. The sensor needs zero gas. See the calibration

instruction of zero-point calibration. The calibration must be confirmed by pushing ENTER.

1

The phrase "time limit" refers to an internal time-out which returns the LCD and the maintenance function back to normal.

2

ENTER is achieved by simultaneously pressing MENU and ESC.

Fig. 7. Push-button menu flow-chart for the AQS61

上海君琼空调科技有限公司，０２１－６０３４１３６６，ｗｗｗ．ｓｈｊｑｋｔ．ｃｏｍ

Содержание AQS51









Отзывы:

Нет отзывов