Honeywell AQS51 Скачать руководство пользователя страница 1

® U.S. Registered Trademark

EN1B-0189GE51 R0102

Copyright © 2002 Honeywell Inc. • All rights reserved

AQS51/61

CO2 / TEMPERATURE SENSOR WITH BUILT-IN CONTROLLER

FOR WALL MOUNTING

INSTALLATION INSTRUCTIONS

GENERAL INFORMATION

The AQS51 and AQS61 CO

2

 / Temperature Sensors are

used to measure the concentration and temperature of

carbon dioxide in indoor air. The units can be configured as

controllers with programmable outputs for both ON/OFF relay

control and the linear control of e.g. mixed air dampers and

fans. The wall mounting housing has been designed with

snap-in features to minimize installation time.

The units can be directly connected to common VAV

(Variable Air Volume) controllers, Direct Digital Control (DDC)

devices, or standalone control systems. The linear output

functions are pre-programmed as CO

2

 and temperature

transmitters. In addition, the AQS51 and AQS61 have a relay

output pre-programmed as a CO

2

 limiter. All functions can be

modified from a PC (Windows 95, 98, NT) using the AQS-

USPxx (version 4.0 or higher) software together with the

AQS3/4-CABLE communication cable.

上海君琼空调科技有限公司,021-60341366,www.shjqkt.com

Содержание AQS51









Отзывы: