Honeywell AlarmNet IGSMV Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 64

Honeywell AlarmNet IGSMV Скачать руководство пользователя страница 50

IGSMV

/

IGSMVCN Installation and Setup Guide

5-4

The second line of the display shows loaded battery voltage.
An asterisk (

*

) next to the voltage indicates that this is below

the accepted level.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

Battery Charger
OK

Battery Charger Status Display

The status of the battery charger circuit of the
IGSMV can be viewed on the 7720P. The status is either OK
or NOT OK.
Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

Line Voltage
xx.xxV

Line Voltage Display

The line voltage of the IGSMV can be viewed on the 7720P.
An asterisk (

*

) next to the voltage indicates that this is below

the accepted level.
Press the [Space] key to go back to the System Status
Display.
Press the backspace [BS] key to go to the previous field.

[T]

Test Msg Sent

Test Alarm

Sends a Test alarm to AlarmNet. Functional for a

registered

IGSMV only. If the device is not registered, a message is
displayed indicating that the command cannot be executed.

[X]

Reset CPU Y/N

Reset the IGSMV.

Pressing [N] returns to diagnostic mode (blank screen = enter
next command or escape).
Pressing [Y] resets the module (blank screen = reset
complete).

[



]

(UP
arrow)

Registering …

Registration

Registers a programmed IGSMV with AlarmNet

.

[



]

(DN
arrow)

Enter PIN#

Registration with PIN for Replacement Module

Registers a replacement IGSMV with AlarmNet, once pro-
grammed, using the existing PIN #.

Force Upload of Configuration File to Server

Pressing [Y] will force the device to upload its entire configu-
ration file to the server.
Pressing [N] cancels the operation.

NOTE:

If the internet is not available, and the IGSMV

module is not initialized when you enter this command, the
following screen will be displayed:

Cannot Upload
Try Later! _

[0]

Force Server Update?

Y/N

Wait for the RSSI LEDs to light, indicating the IGSMV
module has completed its initialization, and try again.

[ENT
ER]

Strt Prog Mode?
Y/N_

Enter Program Mode

Press [Y] to enter program mode; otherwise, press [N].

«
...
48
49
50
51
52
...
»

Содержание AlarmNet IGSMV

































































Отзывы:

Нет отзывов