Honeywell ADEMCO LYNXR-I Security System Скачать руководство пользователя

Страница: 5 / 72

LYNXR-I Installation and Setup Guide

- 5 -

Mounting the Control

Wall Mounting

The illustration below shows the front assembly separated from the back plate.

DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the
front assembly board.

1. Release the front assembly from the back

plate by depressing the two locking tabs

at the top of the unit with the blade of a
medium size screwdriver.

2. Once these tabs have been released,

insert the screwdriver in the side of the
case and release the side locking tabs by
gently twisting.

3. Carefully disconnect the ribbon cable from

the front assembly,

leaving the ribbon

cable connected to the terminal block

PC board

. The back plate contains the

terminal block for making wiring
connections.

4. Mount the back plate to a sturdy wall,

feeding the field wiring through the
appropriate openings in the back plate.

5. After wiring connections are made,

carefully reconnect the ribbon cable to
the front assembly PC board connector
(properly aligning the red wire).

6. Snap the front assembly to the back plate

so it is secured by the locking tabs.

LOCKING

TABS

LOCKING

TABS

LOCKING TABS

RED WIRE

MARKING

DISCONNECT

THIS END ONLY!

07000-003-V1

Desktop Mounting

For desktop use the optional mounting base (model LYNX-DM, purchased separately) must be used.

1. Slide the control panel onto the mounting

base locking tabs.

2. Bring all wiring through the bottom of the

mounting base, using one of the three
wire entry locations, before making
connections to the control panel.

3. Use tie-wraps to secure the wiring to the

built-in wire loops as needed. Use the two
supplied screws to secure the control
panel to the mounting base.

ADD

ESCAPE

DELETE

SELECT

AWAY

OFF

STAY

AUX

01009-004-V1

WIRE ENTRY

KNOCKOUT

(1 of 3)

Содержание ADEMCO LYNXR-I Security System









































































Результаты поиска

Содержание ADEMCO LYNXR-I Security System

Отзывы:

Похожие инструкции для ADEMCO LYNXR-I Security System

Бренды по названию

Популярные бренды

Honeywell ADEMCO LYNXR-I Security System, Инструкция по установке и настройке

Результаты поиска

Содержание ADEMCO LYNXR-I Security System

Отзывы:

Похожие инструкции для ADEMCO LYNXR-I Security System

Бренды по названию

Популярные бренды