Honeywell ADEMCO LYNXR-I Security System Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 72

Honeywell ADEMCO LYNXR-I Security System Скачать руководство пользователя страница 17

LYNXR-I Installation and Setup Guide

- 17 -

Interactive Menu Mode Programming

(

✻

56,

✻

80,

✻

81,

✻

83,

✻

84,

✻

85)

Press

[

✻

]

+

interactive mode No.

(i.e.,

✻

56). The keypad will display the first of a series of prompts. A detailed

procedure (with displays of prompts) is provided in later sections of this manual.

Interactive Mode

Used to Program

✻

56 Enhanced Zone Programming Mode

Zone characteristics, report codes, and serial numbers

✻

80 Device Programming Menu Mode

Powerline Carrier Devices

✻

81 Zone List Menu Mode

Zone Lists for powerline carrier activation

✻

83 Enhanced Sequential Mode

5800 Series transmitter serial numbers

✻

84 Assign Zone Voice Descriptors

Voice descriptors for each zone

✻

85 Record Custom Voice Descriptors

Up to 5 custom voice descriptors for zones

Loading Factory Defaults

To load the factory defaults, enter the Programming mode, press

✻

97, then press number 1, 2, 3, or 4 to

select from default tables

1-4 at the back of this manual, or press “0” if you are not selecting a default table.

If a default table is loaded, any data that has already been programmed into the system will be changed according to the

default table selected!

✻

96

resets all subscriber account numbers and CSID in preparation for an initial download.

Exiting Program Mode

✻

98

inhibits re-entry into the Expert or Voice Prompt Programming modes using the Installer Code.

✻

99

allows re-entry into the Expert Program mode using

Installer Code (4112) + 800

or into the

Voice

Prompt Programming

mode using

Installer Code (4112) + 888

.

Note:

After exiting program mode (or upon power-up), the system takes up to a minute to reset. To bypass the reset
delay, press [#] + [0].

Pass-Thru Programming

This mode allows the Installer to use the LYNXR-I keypad and display to program the communications
device that is connected to the LYNXR-I. Refer to the communications device’s installation instruction to
determine whether this feature is supported.

Entering Pass-Thru Programming mode

1. After power-up, enter the

Installer Code (4112) + 899.

2. Once you have entered Pass-Thru Programming mode “PtP” will be displayed on the keypad.

3. Refer to the Installation Instructions for the LRR/IP Communications Device being installed for

additional programming information.

LYNXR-I will abort this mode:

•

When it receives an abort command from the new communications device.

•

If it fails to communicate with an communications device after 20 attempts.

•

30 minutes after the last key has been pressed.

«
...
15
16
17
18
19
...
»

Содержание ADEMCO LYNXR-I Security System









































































Отзывы:

Нет отзывов